RE5
I.typ
baUd
C.Fos
C.Fos
Baud
Hidden Menu
Parameter Transfer Between Menus
PROGRAMMING DEVICE
Changing Parameters
240
1000
571
1453
1000
571
rE5
1000
571
In "Running Mode", if key pressed for 2 seconds, maximum and minimum measurement values become
equal to the measured value at current time and the message appears on display.
SET
&
SET
unl
Locking and Unlocking
1000
571
Loc
Keys are locked.
Keys are unlocked.
SET
SET
Displaying the Measurement Unit
Measurement
Value
bAr
1000
571
In “Running Mode”, if keys are pressed together for 3 seconds, measurement unit appears. See
Unit
parameter for programming.
&
Setting Up User Calibration Values
&
SET
SET
Programming Mode
I.typ
Factory Defaults
d.Par
Viewing the Revision
r
.
001
&
SET
&
SET
SET
SET
Running Mode Error Messages
L.inp.
H.inp.
Setting Up
Parameters
Measurement Unit (
Unit
)
Err.1
Err.2
C.Err
Displaying the Minimum Measurement Unit
Measurement
Value
In “Running Mode”, if key is pressed for 3 seconds,
minimum measurement value appears.
Measurement
Value
In “Running Mode”, if key is pressed for 3 seconds,
maximum measurement value appears.
Displaying the Maximum Measurement Unit
Resetting Maximum and Minimum Measurement Values
Measurement
Value
Measurement
Value
If keys are pressed together for 2 seconds,
Loc
message appears and keys are
locked. For unlocking, keys are pressed together for 2 seconds,
unL
message
appears and keys are unlocked. If one of the keys is pressed while the device locked,
Loc
message appears on display.
ERROR MESSAGES & DESCRIPTIONS
Error conditions and descriptions are listed below.
*
If voltage or current is difference and lower than half of full scale between
H.inP
and
L.inP
voltage or current.
*
If excessive high-low input current or voltage is applied.
*
If an error occurs during
L.inP
calibration,
Err1
message appears on display.
*
If an error occurs during
H.inP
calibration,
Err2
and
C.Err
message appears on display.
*
If user calibration
is not applied
before and an error occurs during calibration process, device runs according to standard calibration values.
*
If user calibration
is applied
before and an error occurs during calibration process, device runs according to previous user calibration values.
Input voltage or input
current below zero.
Input voltage higher then 15V
or
input current higher than 25mA.
L.INP
calibration
error
Calibration failed
H.INP
calibration
error
If keys are pressed together for 2 seconds,
Pi
message appears and user menu entered. Then in user menu, first parameter's is displayed.
When a parameter selected, if key is pressed selected parameter value appears and displayed parameter can be changed by keys. If no
operation is performed for 3 seconds after the parameter value is being displayed or key is pressed, parameter name will be shown again. While
parameter name displayed, keys are pressed together, returned to "Running Mode" without waiting period.
SET
SET
No calibration required if the standard inputs (0-20mA, 4-20mA, 0-1V and 0-10V) are used.
Cal.t
Parameter should be set as
U.Inp
if no standard input used.
In user menu, if key is pressed for 7 seconds, message appears on display and calibration menu is entered.
L.INP
Voltage or current which are corresponds to
L5Cl
parameter is applied to device input and key is pressed. If operation is success, message appears on
display and proceeding to the next step.
5ucc
SET
In this step, while message displayed, voltage or current which are corresponds to
L5Cl
parameter is applied to device input and key is pressed. If operation is
success, then message appears on display, calibration process is completed and the device will start running according to the new calibration values.
H.inp
5ucc
C.End
SET
If key is
for 7 seconds
P2
message appears on the display and hidden menu is entered. Selected
parameter values can be displayed with key and canged with keys. Accessing to the parameters and
storing functions are as in the user menu. All parameters can be accessed from this menu.
pressed
If keys are pressed together for 2 seconds, parameter transferred to user menu. In this way up to 12
parameters can be transferred to the user menu.
In user menu, if keys are pressed together for 2 seconds, parameter is removed from user menu. When a
parameter is displayed in the user menu, mA LED lights up in the hidden menu.
SET
SET
SET
If pressed key in
Unit
parameter, related digit blinks on display. For desired number, letter or symbol is adjusted by pressing the key for related digit. For
setting up other digits key is pressed. When parameter setting process is completed, by pressing key or no key is pressed for 3 seconds without pressing any
key, parameters can be saved.
Key is held down while the device is powered up,
message will see and restore the factory parameters
In “Running Mode”, if keys are pressed together for 3 seconds,
revision information appears on display.
SİSEL MÜHENDİSLİK ELEKTRONİK SAN. VE TİC. A.Ş.
Şerifali Mah.
Y.Dudullu 34775
ÜMRANİYE/İSTANBUL-
TURKEY
Tel : +90 216 499 46 64 Pbx. Fax : +90 216 365 74 01
url : www.enda.com.tr
Barbaros Cad. No:
18
EI2041-EN-01-
180411
3
/5
ENDA
TM
