SET
mA LED :
If input type is selected as 0-20mA or 4-20mA,
mA LED
lights up.
In "Running Mode", indicates output set value.
In “Programming Mode”, indicates the selected parameter value.
V LED :
If input type is selected as 0-1V or 0-10V,
V LED
lights up.
ALR LED :
If alarm output is active,
ALR LED
lights up. During delay time, LED flashes.
OUT LED :
If “OUT” is active,
OUT LED
lights up. During delay time, LED flashes.
FRONT PANEL
ENDA EI2041
is intended for installation in control panels. Make sure that the device is used only for intended purpose. The shielding
must be grounded on the instrument side. During an installation, all of the cables that are connected to the device must be free of energy.
The device must be protected against inadmissible humidity, vibrations, severe soiling. Make sure that the operation temperature is not
exceeded. All input and output lines that are not connected to the supply network must be laid out as shielded and twisted cables. These
cables should not be close to the power cables or components. The installation and electrical connections must be carried on by a
qualified staff and must be according to the relevant locally applicable regulations.
Panel cut-out
Note :
1)
While panel mounting, additional distance required
for connection cables should be considered.
2)
Panel thickness should be maximum 7mm.
3)
If there is no 60mm free space at back side of the
device, it would be difficult to remove it from the panel.
71,5mm
2
9
,5
m
m
To removing the mounting clamps :
-
Push the flush-mounting
clamps in direction
1
-
Pull out the clamps in direction
2
.
Depth
Rubber packing
2
71mm
5mm
Panel
3
5
m
m
77mm
DIMENSIONS
CONNECTION DIAGRAM
EI2041-230
PROGRAMMABLE INDICATOR
Made in Turkey
1
2
3
4
5
6
7
8
9
10
ENDA
INDUSTRIAL ELECTRONICS
SN: XXXXXXXXX
230V AC
50/60Hz
11 12
8 680407 721603
INPUT
+
GND
11 12 13
A
B
COM
EI2041-230-2R-05-RS
PROGRAMMABLE INDICATOR
Made in Turkey
1
2
3
4
5
6
7
8
9
10
ENDA
INDUSTRIAL ELECTRONICS
SN: XXXXXXXXX
230V AC
50/60Hz
8 680407 722204
INPUT
+
GND
OUT
250V 8A~
AUX SUPPLY
+
GND
ALARM
250V 8A~
Flush
mounting
clamp
1
IN
P
U
T
+
G
N
D
1
2
3
4
5
6
7
8
9
10
11
12
EN
DA
IN
DU
ST
RIA
L E
LE
CT
RO
NIC
S
2
3
0
V
A
C
+
1
0
%
-
2
0
%
5
0
/6
0
H
z
7
V
A
SN
: X
XX
XX
XX
XX
Ma
de
In
T
urk
ey
Flush
mounting
clamp
1
2
2
86
804
07
721
603
EI2
04
1-2
30
PR
OG
RA
MM
AB
LE
IN
DIC
AT
OR
In "Running Mode", indicates the maximum measured value.
Used for incrementing values in "Programming Mode".
In "Running Mode", indicates the minimum measured value.
Used for decrementing values in "Programming Mode".
Flush
mounting
clamp
1)
Mains supply cords shall meet the requirements of IEC 60227 or IEC 60245.
2)
In accordance with the safety regulations, the power supply switch shall bring the identification of the relevant instrument and it
should be easily accessible by the operator.
Note :
2
1
184-253V AC
50/60Hz 7VA
230V AC
Supply
Switch
Cable size: 1,5mm²
Fuse
F 100 mA
250V AC
Neutral
Line
SUPPLY :
NOTE :
Fuse should
be connected
Holding screw
0.4-0.5Nm.
Equipment is protected throughout by
DOUBLE INSULATION
SİSEL MÜHENDİSLİK ELEKTRONİK SAN. VE TİC. A.Ş.
Şerifali Mah.
Y.Dudullu 34775
ÜMRANİYE/İSTANBUL-
TURKEY
Tel : +90 216 499 46 64 Pbx. Fax : +90 216 365 74 01
url : www.enda.com.tr
Barbaros Cad. No:
18
EI2041-EN-01-
180411
2
/5
ENDA
TM
EI2041
mA
V
ALR OUT
EI2041
mA
V
ALR OUT
Please see page 5 for Modbus Connection Diagram
