ENCON SHOWER SHELTER Manual Download Page 5 | Manualshive

Page: 5 / 10

background image

Doc. No: 01999929

Revision: C

5 of 10

Issue Date: 08/15/21

PART III

FRONT AND REAR STRUCURE ASSEMBLY.

1. Connect the side structures created in

PART II

by inserting (2) ITEM 11’s between the ITEM 2’s at the top, and by

inserting (1) ITEM 11 between the ITEM 3’s at the bottom. Tighten hex screws.

SEE FIGURE 9.

FIGURE

9

2. Raise structure and locate near the shower equipment. If required remove the ITEM 11 located on the bottom to

allow the structure to be placed around the shower equipment reconnect ITEM 11 afterwards.

«
...
3
4
5
6
7
...
»

Summary of Contents for SHOWER SHELTER











Reviews:

No comments

Related manuals for SHOWER SHELTER

Brand: California Faucets Pages: 2

AXISS FUSION PLUS AXFSPCSMC

Brand: Felton Pages: 6

Brand: T&S Pages: 12

Brand: Fresca Pages: 2

Brand: eurostream Pages: 8

Brand: Gessi Pages: 24

Brand: Moen Pages: 1

Brand: Transform Pages: 32

Brand: bioBidet Pages: 12

Metropol Classic 31306 1 Series

Brand: Hans Grohe Pages: 20

Montreux 16583 1 Series

Brand: Hans Grohe Pages: 16

Tango C 04270 5 Series

Brand: Hans Grohe Pages: 16

Talis S 72200 1 Series

Brand: Hans Grohe Pages: 16

Talis Elegance 33405 Series

Brand: Hans Grohe Pages: 8

Talis N 220 U-Style 1Jet 72806 1 Series

Brand: Hans Grohe Pages: 20

Metropol 14837 Series

Brand: Hans Grohe Pages: 40

Metropol 14615 Series

Brand: Hans Grohe Pages: 16

Tecturis S 110 Fine CoolStar 73320 Series

Brand: Hans Grohe Pages: 44

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands