background image

Doc. No: 01999929 

Revision: C 

 

10 of 10 

Issue Date: 08/15/21 

 

OPERATION & MAINTENANCE 

1.  Plumbed units shall be activated weekly to flush lines and verify proper flow pattern and volume.  
2.  Test records should be maintained verifying compliance with testing procedures. 
3.  Some chemical vapors or liquids may damage or soften plastic materials. Precaution should be taken to determine 

compatibility prior to installation. 

TRAINING 

All employees who might be exposed to hazardous material shall be instructed in the location and proper use of emergency 
shower and eye/facewash units. Experiences have shown that initial first-aid treatment for irritates should be to wash the eyes 
and face for 15 minutes prior to medical treatment. It is important to hold the eyelids open and roll the eyes so water will flow 
on all surfaces and in the folds surrounding the eyes. 

PROPOSITION 65 

WARNING: This product can expose you to BPA, which is known to the State of California to cause birth defects or other 
reproductive harm. For more information go to www.P65Warnings.ca.gov. 

WARRANTY STATEMENT 

ENCON  HEREBY  DISCLAIMS  ALL  WARRANTIES  EXPRESSED  OR  IMPLIED  INCLUDING  BUT  NOT  LIMITED  TO 
WARRANTIES  OF  MERCHANTABILITY,  FITNESS  FOR  A  PARTICULAR  PURPOSE,  AND  NON-INFRINGEMENT  OF 
THIRD-PARTY RIGHTS, EXCEPT AS HEREINAFTER PROVIDED. 

Encon Safety Products warrants that for one year from the date of purchase of any Encon products, the product will be free of 
defects in materials and workmanship if properly used and cared for or cleaned under normal conditions in accordance with 
Encon’s use and care instructions and properly installed, if applicable, in accordance with Encon’s installation instructions. 
With  respect  to  the  product,  Encon’s  only  obligation  and  purchaser’s  exclusive  remedy  under  this  warranty  is  to  repair  or 
replace such product; provided that: 

1.  Encon is notified of the defect within one year of shipment, and 
2.  the product is determined by Encon to be defective. 

Encon requires proof of original ownership as proof of warranty coverage, and Encon must receive any claim under this Limited 
Warranty within one year of purchase of the product. 

NOTWITHSTANDING  ANYTHING  TO  THE  CONTRARY  CONTAINED  HEREIN,  ENCON  SHALL  NOT  BE  LIABLE  FOR 
LOSS,  DAMAGE,  OR  EXPENSE  ARISING  DIRECTLY  OR  INDIRECTLY  AS  A  CONSEQUENCE  OF  USE  OF  THE 
EQUIPMENT  WITH  OTHER  PRODUCTS  OR  FROM  ANY  OTHER  CAUSE,  INCLUDING  ANY  CONSEQUENTIAL, 
INCIDENTAL, SPECIAL OR EXEMPLARY DAMAGES, EXCEPT FOR ENCON’S OBLIGATION TO REPAIR OR REPLACE 
DEFECTIVE PRODUCTS AS EXPRESSLY PROVIDED IN THIS STATEMENT. 

Replacement parts purchased from Encon are warranted for one year following the shipment of such replacement part, or until 
the expiration of the warranty period for the product, whichever is less. No warranty is given in connection with products that 
are altered without Encon’s expressed written consent. The same warranty limitations and the obligations of Encon as set out 
herein above shall apply to replacement parts. 

Encon’s  total  liability  arising  out  of  this  warranty  (including,  but  not  limited  to,  warranty  claims)  regardless  of  forum  and 
regardless of whether such action or claim is based on tort, contract or otherwise will not exceed the total purchase price of 
the product. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

6825 W. Sam Houston Pkwy. N 

Houston, TX 77041 

1-800-AT-ENCON / 1-800-283-6266 

[email protected]

 

http://www.enconsafety.com 

Summary of Contents for SHOWER SHELTER











Reviews: