background image

12430-11-1008

Page 4

SAFETY INFORMATION FOR USERS OF LP-GAS

Propane (LP-Gas) is a flammable gas which can cause fires 

and explosions. In its natural state, propane is odorless and 

colorless. You may not know all the following safety precau-

tions which can protect both you and your family from an 

accident. Read them carefully now, then review them point 

by point with the members of your household. Someday, 

when there may not be a minute to lose, everyone’s safety 

will depend on knowing exactly what to do.  If, after read-

ing the following information, you feel you still need more 

information, please contact your gas supplier.

LP-GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.

That’s your signal to go into immediate action!

•  Do  not  operate  electric  switches,  light  matches,  use  your 

phone. Do not do anything that could ignite the gas.

•  Get everyone out of the building, vehicle, trailer, or area. Do 

that IMMEDIATELY.

•  Close all gas tank or cylinder supply valves.
•  LP-Gas is heavier than air and may settle in low areas such 

as basements. When you have reason to suspect a gas leak, 

keep out of basements and other low areas. Stay out until 

firefighters declare them to be safe.

•  Use your neighbor’s phone and call a trained LP-Gas service 

person and the fire department. Even though you may not 

continue to smell gas, do not turn on the gas again. Do not 

re-enter the building, vehicle, trailer, or area.

• 

Finally,

 let the service man and firefighters check for escaped 

gas. Have them air out the area before you return. Properly 

trained LP-Gas service people should repair the leak, then 

check and relight the gas appliance for you.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot smell the 

odor of the chemical put into the gas. You must find out if you 

can smell the odorant in propane.

 Smoking can decrease your 

ability to smell. Being around an odor for a time can affect your 

sensitivity or ability to detect that odor. Sometimes, other odors 

in the area mask the gas odor. People may not smell the gas odor 

or their minds are on something else. Thinking about smelling a 

gas odor can make it easier to smell.

The odorant in LP-Gas is colorless, and it can fade under 

some circumstances.

 For example, if there is an underground 

leak, the movement of the gas through soil can filter the odorant. 

Odorants in LP-Gas are subject to oxidation. This fading can oc-

cur if there is rust inside the storage tank or in iron gas pipes.

The odorant in escaped gas can adsorb or absorb onto or into 

walls, masonry and other materials and fabrics in a room. That 

will take some of the odorant out of the gas, reducing its odor 

intensity.

LP-Gas may stratify in a closed area, and the odor intensity could 

vary at different levels. Since it is heavier than air, there may be 

more odor at lower levels. Always be sensitive to the slightest 

gas odor. If you detect any odor, treat it as a serious leak. Imme-

diately go into action as instructed earlier.

SOME POINTS TO REMEMBER

• 

Learn to recognize the odor of LP-gas.

 Your local LP-Gas 

Dealer can give you a “Scratch and Sniff” pamphlet. Use it 

to find out what the propane odor smells like. If you suspect 

that your LP-Gas has a weak or abnormal odor, call your 

LP-Gas Dealer.

•  If you are not qualified, do not light pilot lights, perform 

service, or make adjustments to appliances on the LP-Gas 

system.  If  you  are  qualified,  consciously  think  about  the 

odor of LP-Gas prior to and while lighting pilot lights or 

performing service or making adjustments.

•  Sometimes a basement or a closed-up house has a musty 

smell that can cover up the LP-Gas odor. Do not try to light 

pilot lights, perform service, or make adjustments in an area 

where the conditions are such that you may not detect the 

odor if there has been a leak of LP-Gas.

•  Odor fade, due to oxidation by rust or adsorption on walls 

of new cylinders and tanks, is possible. Therefore, people 

should be particularly alert and careful when new tanks or 

cylinders are placed in service. Odor fade can occur in new 

tanks, or reinstalled old tanks, if they are filled and allowed 

to set too long before refilling. Cylinders and tanks which 

have been out of service for a time may develop internal rust 

which will cause odor fade. If such conditions are suspected 

to exist, a periodic sniff test of the gas is advisable. 

If you 

have any question about the gas odor, call your LP-Gas 

Dealer. Aperiodic sniff test of the LP-Gas is a good safety 

measure under any condition.

•  If, at any time, you do not smell the LP-Gas odorant and you 

think you should, assume you have a leak. Then take the same 

immediate action recommended above for the occasion when 

you do detect the odorized LP-Gas.

•  If you experience a complete “gas out” (the container is un-

der no vapor pressure), turn the tank valve off immediately. 

If the container valve is left on, the container may draw in 

some air through openings such as pilot light orifices. If this 

occurs, some new internal rusting could occur. If the valve is 

left open, then treat the container as a new tank. Always be 

sure your container is under vapor pressure by turning it off 

at the container before it goes completely empty or having 

it refilled before it is completely empty.

Summary of Contents for DVC-35























Reviews: