background image

30067-2-0315

Page 4

SAFETY INFORMATION FOR USERS OF LP-GAS

LP-Gas (Propane) is a flammable gas which can cause fires 

and explosions. In its natural state, propane is odorless and 

colorless. You may not know all the following safety precautions 

which can protect both you and your family from an accident. 

Read them carefully now, then review them point by point with the 

 

members of your household. Someday, there may not be a 

minute to lose, everyone’s safety will depend on knowing ex

-

actly what to do. If, after reading the following information, you 

feel you still need more information, please contact your gas 

supplier.

LP-GAS WARNING ODOR

If a gas leak happens, you should be able to smell the gas because of the odorant put in the LP-Gas.

That’s your signal to go into immediate action!

•  Do not operate electric switches, light matches, use your 

phone. Do not do anything that could ignite the gas.

•  Get everyone out of the building, vehicle, trailer, or area. 

Do that IMMEDIATELY.

•  Close all gas tank or cylinder supply valves.

•  LP-Gas is heavier than air and may settle in low areas 

such as basements. When you have reason to suspect 

a gas leak, keep out of basements and other low areas. 

Stay out until firefighters declare them to be safe.

•  Use  your  neighbor’s  phone  and  call  a  trained  LP-Gas 

 

service  person  and  the  fire  department.  Even  though 

you  may  not  continue  to  smell  gas,  do  not  turn  on  the 

gas  again.  Do  not  re-enter  the  building,  vehicle,  trailer, 

or area.

•  Finally, let the service man and firefighters check for es

-

caped gas. Have them air out the area before you return. 

Properly trained LP-Gas service people should repair the 

leak, then check and relight the gas appliance for you.

NO ODOR DETECTED - ODOR FADE

Some people cannot smell well. Some people cannot smell 

the odor of the chemical put into the gas. You must find out if 

you can smell the odorant in propane. Smoking can decrease 

your ability to smell. Being around an odor for a time can affect 

your sensitivity or ability to detect that odor. Sometimes other 

odors in the area mask the gas odor. People may not smell 

the gas odor or their minds are on something else. Thinking 

about smelling a gas odor can make it easier to smell.
The  odorant  in  LP-Gas  is  colorless,  and  it  can  fade  under 

some circumstances. For example, if there is an underground 

leak, the movement of the gas through soil can filter the odor

-

ant. Odorants in LP-Gas also are subject to oxidation. This 

fading can occur if there is rust inside the storage tank or in 

iron gas pipes.

The  odorant  in  escaped  gas  can  adsorb  or  absorb  onto  or 

into walls, masonry and other materials and fabrics in a room. 

That will take some of the odorant out of the gas, reducing its 

odor intensity.
LP-Gas may stratify in a closed area, and the odor intensity 

could vary at different levels. Since it is heavier than air, there 

 

may be more odor at lower levels. Always be sensitive to the 

slightest gas odor. If you detect any odor, treat it as a serious leak. 

 

Immediately go into action as instructed earlier.

SOME POINTS TO REMEMBER

•  Learn to recognize the odor of LP-Gas. Your local LP-Gas 

Dealer can give you a “Scratch and Sniff” pamphlet. Use 

it to find out what the propane odor smells like. If you sus

-

pect that your LP-Gas has a weak or abnormal odor, call 

your LP-Gas Dealer.

•  If you are not qualified, do not light pilot lights, perform 

 

service, or make adjustments to appliances on the LP-

Gas system. If you are qualified, consciously think about 

the odor of LP-Gas prior to and while lighting pilot lights 

or performing service or making adjustments.

•  Sometimes a basement or a closed-up house has a musty 

smell that can cover up the LP-Gas odor. Do not try to 

light pilot lights, perform service, or make adjustments in 

an area where the conditions are such that you may not 

detect the odor if there has been a leak of LP-Gas.

•  Odor fade, due to oxidation by rust or adsorption on walls 

of new cylinders and tanks, is possible. Therefore, people 

should be particularly alert and careful when new tanks or 

cylinders are placed in service. Odor fade can occur in new 

tanks, or reinstalled old tanks, if they are filled and allowed 

to set too long before refilling. Cylinders and tanks which 

have been out of service for a time may develop internal 

rust  which  will  cause  odor  fade.  If  such  conditions  are 

 

suspected  to  exist,  a  periodic  sniff  test  of  the  gas  is 

 

advisable. If you have any question about the gas odor, 

call your LP-Gas dealer. A periodic sniff test of the LP-

Gas is a good safety measure under any condition.

•  If, at any time, you do not smell the LP-Gas odorant and 

you think you should, assume you have a leak. Then take 

the same immediate action recommended above for the 

 

occasion when you do detect the odorized LP-Gas.

•  If  you  experience  a  complete  “gas  out,”  (the  container 

 

is  under  no  vapor  pressure),  turn  the  tank  valve  off 

 

immediately. If the container valve is left on, the container 

may draw in some air through openings such as pilot light 

orifices.  If  this  occurs,  some  new  internal  rusting  could 

 

occur. If the valve is left open, then treat the container as 

a new tank. Always be sure your container is under vapor 

pressure by turning it off at the container before it goes 

 

completely  empty  or  having  it  refilled  before  it  is 

 

completely empty.

Summary of Contents for BF28(B,C,G)M(K)(N,P)-5





























Reviews: