background image

37406-5-0320

Page 3

THIS IS A HEATING APPLIANCE

DO NOT OPERATE THIS APPLIANCE WITHOUT FRONT PANELS INSTALLED.

•  Due  to  high  temperatures,  the  appliance  should  be 

located  out  of  traffic  and  away  from  furniture  and 

draperies.

•  Children and adults should be alerted to the hazards 

of high surface temperatures and should stay away to 

avoid burns or clothing ignition.

•  Young children should be carefully supervised when 

they are in the same room as the appliance.

•  Clothing  or  other  flammable  material  should  not  be 

placed on or near the appliance.

•  Any  safety  screen  or  guard  removed  for  servicing 

an appliance must be replaced prior to operating the 

appliance.

•  Keep burner and control compartment clean.

• 

Installation and repair should be done by a QUALIFIED 

SERVICE PERSON. The appliance should be inspected 

before use and at least annually by a qualified service 

person. More frequent cleaning may be required due 

to excessive lint from carpeting, bedding materials, 

etc. It is imperative that control compartments, burners 

and circulating air passageways of the appliance be 

kept clean.

•  Do  NOT  put  anything  around  the  furnace  that  will 

obstruct the flow of combustion and ventilation air.

•  DO  keep  the  appliance  area  clear  and  free  from 

combustible material, gasoline and other flammable 

vapors and liquids.

•  DO examine venting system periodically and replace 

damaged parts.

•  DO make a periodic visual check of pilot and burners. 

Clean and replace damaged parts.

•  CAUTION: Pilot hole cover must be kept tightly closed 

during operation.

•  DO NOT use this heater if any part has been under 

water. Immediately call a qualified service technician 

to inspect the heater and to replace any part of the 

control system and any gas control which has been 

under water.

•  This furnace must not be connected to a chimney flue 

serving a separate soid-fuel burning appliance.

When an existing Category 1 heater is removed or replaced, the 

original venting system may no longer be sized to properly vent the 

attached appliances. Instructions shall also indicate effects of an 

improperly sized venting system (formation of condensate, leakage, 

spillage, etc.) and shall specify the following test procedure:

 

 WARNING

CARBON MONOXIDE POISONING HAZARD

Failure  to  follow  the  steps  outlined  below  for  each 

appliance  connected  to  the  venting  system  being  placed 

into operation could result in carbon monoxide poisoning 

or death.

The  following  steps  shall  be  followed  for  each  appliance 

connected  to  the  venting  system  being  placed  into 

operation,  while  all  other  appliances  connected  to  the 

venting system are not in operation:

1. 

Seal any unused openings in the venting system.

2. 

Inspect  the  venting  system  for  proper  size  and 

horizontal pitch, as required in the National Fuel Gas 

Code, ANSI Z223.1/NFPA 54 or the Natural Gas and 

Propane  Installation  Code,  CSA  B149.1  and  these 

instructions.  Determine  that  there  is  no  blockage  or 

restriction,  leakage,  corrosion  and  other  deficiencies 

which could cause an unsafe condition.

3. 

As  far  as  practical,  close  all  building  doors  and 

windows  and  all  doors  between  the  space  in  which 

the appliance(s) connected to the venting system are 

located and other spaces of the building.

4. 

Close fireplace dampers.

5. 

Turn on clothes dryers and any appliance not connected 

to the venting system. Turn on any exhaust fans, such 

as  range  hoods  and  bathroom  exhausts,  so  they  are 

operating  at  maximum  speed.  Do  operate  a  summer 

exhaust fan.

6. 

Follow  the  lighting  instructions.  Place  the  appliance 

being  inspected  into  operation.  Adjust  the  thermostat 

so appliance is operating continuously.

7. 

Test for spillage from draft hood equipped appliances 

at the draft hood relief opening after 5 minutes of main 

burner operation. Use the flame of a match or candle.

8. 

If  improper  venting  is  observed  during  any  of  the 

above tests, the venting system must be corrected in 

accordance with National Fuel Gas Code, ANSI Z223.1/

NFPA 54 and/or Natural Gas and Propane Installation 

Code, CSA B149.1.

9.  After  is  has  been  determined  that  each  appliance 

connected 

to the venting system properly vents when 

tested  as  outlined  above,  return  doors,  windows, 

exhaust fans, fireplace dampers and any other gas-fired 

burning appliance to their previous conditions of use.

Summary of Contents for FAW55SPPXLP-1

































Reviews: