background image

Upflow / Horizontal — Downflow / Horizontal,
Gas-Fired Furnaces, “Fan Assisted
Combustion System”

Installer’s Guide

Upflow / Horizontal*

Downflow / Horizontal*

For VENT SIZING INFORMATION see:

USA —

National Fuel Gas Code ....... ANSI Z223.1/NFPA 54 (latest version)

CANADA —

Natural Gas Installation Code ..... CAN/CGA-B149.1 (latest version)
Propane Installation Code ............ CAN/CGA-B149.2 (latest version)

USA/CANADA ALTERNATE —

Category I Venting Guide ............................... Pub. No. 18-CH23D1-2

*Horizontal Conversion for these furnaces may be left or right side rotation.

ALL phases of this installation must comply with NATIONAL, STATE AND LOCAL CODES

IMPORTANT —

This Document is 

customer property

 and is to remain with this unit.

Please return to service information pack upon completion of work.

*First letter may be “A” or “T”

*UD1A040A9241A
*UD1A040A9301A
*UD1A060A9241A
*UD1A060A9361A
*UD1B060A9361A

*UD1B080A9241A
*UD1B080A9361A
*UD1B080A9481A
*UD1C080A9601A
*UD1B100A9361A

*UD1B100A9451A
*UD1C100A9481A
*UD1C100A9601A
*UD1D100A9721A
*UD1C120A9541A

*UD1D120A9601A
*UD1D140A9601A
*DD1A040A9241A
*DD1A060A9241A
*DD1A060A9361A

*DD1B060A9361A
*DD1B080A9361A
*DD1B080A9451A
*DD1B100A9451A
*DD1C100A9481A

*DD1C100A9541A
*DD1C120A9541A
*DD1D120A9601A
*DD1D140A9601A

1 8 - CD1 9 D7 - 2 2

A341789P01

Summary of Contents for DD1A040A9241A Series

























Reviews: