background image

25476-5-0612

Page 3

The installation must conform with local codes or, in 

the absence of local codes, with the National Fuel Gas 

Code, ANSI Z223.1 (latest edition) and to the National 

electrical Code, ANSI/NFpA70 (latest edition).

NOTE: Installation and repair should be done by a quali

-

fied service person. The appliance should be inspected 

before use and at least annually by a qualified service 

person. More frequent cleaning may be required due 

to excessive lint from carpeting, bedding material, etc. 

It is imperative that control compartment, burners and 

circulating air passageways of the appliance be kept 

clean.

Any safety screen or guard removed for servicing an 

appliance must be replaced prior to operating the appli

-

ance. Provide adequate combustion and ventilation air.
The flow of combustion and ventilation air MUST NOT 

be obstructed.

provide adequate clearance around air openings into 

the  combustion  chamber  and  adequate  accessibility 

clearance for servicing and proper operation. NEVER 

obstruct the front opening of the appliance.

This  Empire  Comfort  Systems,  Inc.  firebox  and  its 

components have been tested and will operate safely 

when installed in accordance with this installation 

manual. Read all instructions before starting installation, 

then follow these instructions carefully during 

installation  to  maximize  firebox  benefit  and  safety. 

Report to your dealer any parts damaged in shipment.

The  Empire  Comfort  Systems,  Inc.  warranty  will  be 

voided by, and Empire Comfort Systems, Inc. disclaims 

any responsibility for the following actions:

-  Installation of any damaged firebox.

-  Modification of the firebox or any of the components 

parts thereof.

-  Installation  other  than  as  instructed  by  Empire 

Comfort Systems, Inc.

-  Installation and/or use of any component part 

or  accessory  not  approved  by  Empire  Comfort 

Systems,  Inc.  in  combination  or  assembly  with 

a  Empire  Comfort  Systems,  Inc.  firebox,  not 

withstanding  any  independent  testing  laboratory 

or other third party approval of such component 

part or accessory.

Any such action may create a possible fire hazard.

Consult your local building codes.
Firebox Screen.

The firebox screen must be in place when the firebox 

is operating.

Instructions to Installer

1.  installer must leave instruction manual with owner after 

installation.

2.  Installer must have owner fill out and mail warranty card 

supplied with firebox.

3.  installer should show owner how to start and operate 

log set that is installed into firebox.

Important

all correspondence should refer to complete Model number, 

Serial number.
notice:

  During  initial  firing  of  this  firebox  with  a  log  set 

installed, its paint will bake out, and smoke will occur. to 

prevent triggering of smoke alarms, ventilate the room in 

which the unit is installed.

Qualified Installing Agency

installation and replacement of gas piping, gas utilization 

equipment or accessories and repair and servicing of 

equipment shall be performed only by a qualified agency. 

The  term  "qualified  agency"  means  any  individual,  firm, 

corporation or company which either in person or through 

a representative is engaged in and is responsible for (a) 

the installation or replacement of gas piping or (b) the 

connection, installation, repair or servicing of equipment, 

who is experienced in such work, familiar with all precautions 

required and has complied with all the requirements of the 

authority having jurisdiction.

State of Massachusetts: the installation must be made 

by a licensed plumber or gas fitter in the Commonwealth 

of Massachusetts. the state of Massachusetts requires 

that a flexible appliance connector cannot exceed three 

feet in length.
Sellers of unvented propane or natural gas-fired 

supplemental room heaters shall provide to each 

purchaser a copy of 527 cMR 30 upon sale of the unit.
in the State of Massachusetts, unvented propane and 

natural  gas-fired  space  heaters  shall  be  prohibited  in 

bedrooms and bathrooms.

the installation must conform with local codes or, in the 

absence of local codes, with the national Fuel gas code, 

anSi Z223.1/nFPa 54.*

*available from the american national Standards institute, 

inc., 11 West 42nd St., new York, n.Y. 10036.

IMpORTANT SAFETy INFORMATION

INTRODUCTION

Summary of Contents for VFD32FB0F-2

























Reviews: