background image

 

 

Instruction elliptical trainer 900 / 900 med

 

Version 1.1 07.06.2022

 

Page 11 from 13 

 

Fault detection (malfunction) guide  

If any faults occur on the equipment that you cannot classify, please contact emotion fitness GmbH & Co.KG. For each 
error  message,  you  should  have  the  serial  number  and  model  type  of  the  defective  device  ready,  as  this  could  be 
important  in  order  to  be  able  to  make  the  correct  diagnosis  and,  above  all,  to  provide  the  appropriate  replacement 
parts for you! 

Maintenance instructions for the operator 

Ideally, visually inspect the unit before each use, but at least daily, and pay particular attention to defective parts, loose 
connections and atypical noises. 
 
The following checks must be carried out at least every 6 months: 

  Visually inspect all visible joints, as well as welds. 

  Clean the unit thoroughly. 

  Check all screw connections for tightness. 

  Check the integrity and strength of the pedals and cranks. 

 

Generally speaking: 

  Clean the plastic casing and frame parts regularly as required with a damp cloth and mild soap, then wipe 

dry again. 

  The use of spray bottles with cleaning agents is not permitted; it has been shown that the units never 

become dry in inaccessible places. Rust infestation cannot be ruled out by this procedure. 

  Make sure that no liquid gets into the monitor housing,  

  For any necessary disinfection of the devices, please use only mikrozid® sensitive wipes disinfectant 

wipes 

(

http://www.schuelke.com/). 

  The monitor display may show a capacitor voltage that is too low, at which a function without braking 

current cannot be safely guaranteed. You can recharge the capacitor by pedalling with a higher load or a 
power supply unit approved by the device manufacturer. 

  Check the housing fixings for tightness. 

  We recommend a regular visual inspection of all parts of the unit, especially screws, welds and other 

fixings. 

  Check that the feet of the appliance are firmly seated. 

  Only use original spare parts - contact us for this. 

 

Maintenance by authorised specialist 

In case of problems with the device that you cannot solve yourself in a simple way, always contact the emotion fitness 
service. The authorised service will help you quickly and competently or provide you with instructions

Summary of Contents for motion cross 900














Reviews: