manualshive.com logo in svg

EMKO ESM-7311-H, Instruction Manual, Page: 27 / 30

Share
Download
EMKO ESM-7311-H Instruction Manual Download Page 27

4.8 Entering to the Programming Mode, Changing and Saving Parameters

Main Operation Screen

If no operation is performed in programming mode for 20 seconds, device turns to
main operation screen automatically.

i

°C

SV

PR

°C

SV

PR

°C

SV

PR

°C

SV

PR

When SET button is

pressed for 5 seconds,
“PR” led starts to blink.

If programming mode

entering password is

different from 0,

programming mode

entering screen

is observed.

Note-1:

If programming mode accessing password is 0, hysteresis screen

is observed

instead of programming screen accessing password

Programming Mode

Entering Screen

Press increment

button for accessing

to the password

entering screen.

Enter programming

mode accessing

password with increment

and decrement buttons.

Note-2:

Parameters can be observed by pressing SET/OK button in password entering screen

without entering the programming mode entering password. But parameters can not be
changed.

Password

Entering Screen

Press SET/OK

button for

accessing to the

parameters.

°C

SV

PR

°C

SV

PR

°C

SV

PR

Hysteresis

Parameter

Programming Screen

°C

SV

PR

Press increment button
for accessing to the
parameter value. Press
set button for accessing
to the next parameter.

Programming Screen

Hysteresis

Parameter

Change the value

with increment and

decrement buttons.

Press set button for

saving the parameter.

Press set button

for accessing to

the next parameter.

27

Hysteresis

Value

Hysteresis

Value

Password

Entering Screen

Summary of Contents for ESM-7311-H































Reviews:

No comments