manualshive.com logo in svg

EMKO ESM-7311-H, Instruction Manual, Page: 22 / 30

Share
Download
EMKO ESM-7311-H Instruction Manual Download Page 22

22

Minimum Alarm Parameter

It can be adjusted from minimum scale of the device to maximum alarm value (AuH).

( Default = Input Type Minimum Scale )

Relative alarm is selected. Alarm operates according to the set value. If
temperature is below ( Set -

) or above ( Set +

) , alarm

occurs.

Temperature Alarm Function Selection Parameter ( Default = 0 )

Temperature Alarm function is inactive.

Absolute alarm is selected. If temperature is lower than

and higher

than

, then alarm is on.

Maximum Alarm Parameter (Default = Input Type Maximum Scale)

It can be adjusted from minimum alarm value (AuL) to maximum scale of the device.

Alarm Delay Parameter ( Default = 0 )

If an alarm occurs, delay can be defined with this parameter. It can be adjusted from 0
To 99 minutes.

Alarm Delay After Power On Parameter (Default = 0)

This parameter defines the delay for the alarm is being active after power on. It can
be adjusted from 0 to 99 minutes.

Buzzer Function Selection Parameter ( Default = 1 )

Buzzer is inactive.

Buzzer is active at the end of the cooking time.

Buzzer is active if an alarm occurs.

Buzzer is active during sensor failures.

Buzzer is active at the end of the cooking time, alarm or sensor failures.

Temperature Controlling Continuity Selection Parameter

Temperature controlling can be continues or stopped according to the selection. This
parameter can be observed if cooking time (Timer)

is

1

³

( Default = 0 )

Continuous Operation :

Temperature control starts after the temperature

control starting delay at power on

is expired and continues. If buzzer

function selection parameter

Is 1 or 4, at the end of the cooking time,

(Timer) internal buzzer operates to indicate cooking time has finished.

Interrupted Operation :

Temperature control starts after temperature

control starting delay at power on

is expired. Temperature control

can be stopped at the end of the cooking time (Timer) or by pressing
cooking ON/OFF button or when

Temperature control does not start till cooking ON/OFF

button is pressed again or when

cooking time start/stop input is getting

open condition.

cooking time start/stop input is getting

closed condition again.

Cooking Time Starting Conditions Parameter

This parameter can be observed if cooking time (Timer)

is 1.

³

( Default = 0 )

Cooking time (Timer) is started with cooking ON/OFF button or when
cooking time start/stop input is getting closed condition.
Cooking time (Timer) is started when temperature reaches to the process
set value after pressing cooking ON/OFF button or when cooking time
start/stop input is getting closed condition.

Summary of Contents for ESM-7311-H































Reviews:

No comments