manualshive.com logo in svg

EMKO ESM-7311-H, Instruction Manual, Page: 23 / 30

Share
Download
EMKO ESM-7311-H Instruction Manual Download Page 23

°C

SV

PR

Main Operation

Screen

3 secs.

23

Buzzer is Active During This Time

This parameter can be observed if buzzer function selection

is 1.

It can be adjusted from 1 to 99 minutes. When this parameter is 1, if decrement button
is pressed,

is observed. Then buzzer becomes active till buzzer silence button

³

( Default =

)

Button Protection Parameter ( Default = 0 )

There is no protection

Cooking time(Timer) can not be changed. Cooking ON/OFF operation is
not performed.
SET value can not be changed

Cooking time (Timer) and set value can not be changed. Cooking ON/OFF
operation is not performed.

Programming Mode Accessing Password

Password for entering to the programming mode is defined with this parameter.
It can be adjusted from 0 to 999. If it is 0, programming mode accessed without
entering password.

( Default = 0 )

Cooking time (Timer) and set value can not be changed. Cooking ON/OFF
operation is performed when

button is pressed.

7

8

DIGITAL INPUT

K

When K switch that is connected to the cooking time
start/stop input, getting closed condition, cooking
time (Timer) is started and cooking time active led
becomes active. While cooking time (Timer)
continues if K switch getting open condition, cooking
time (Timer) is finished and cooking time active led
lights off.

4.5.2 Cooking Time (Timer) ON/OFF Operation with Cooking Time Start/Stop Input

4.5 Cooking Time (Timer) ON/OFF Operation

4.5.1 Cooking Time (Timer) ON/OFF Operation with Cooking Button

In main operation screen, If cooking button is
pressed for 3 seconds, then cooking time (Timer) is
started and cooking time active led becomes active.
While cooking time (Timer) continues if cooking
button is pressed for 3 seconds, cooking time (Timer)
is finished and cooking time active led lights off.
If button protection parameter

= 4 cooking time

(Timer) ON/OFF operation is performed when

button is pressed.

Summary of Contents for ESM-7311-H































Reviews:

No comments