background image

9

©2020 EMist is a registered trademark of SanoTech 360 LLC., 

all rights reserved. EMist is a wholly owned subsidiary of SanoTech 360 LLC.

TIP:

 

IT IS GOOD PRACTICE TO FLUSH THE APPLICATION 

SYSTEM EVERY 24 HOURS WITH CLEAN WATER.  DO 
NOT STORE CHEMICALS IN THE RESERVOIR WHILE THE 
SYSTEM IS NOT IN USE FOR GREATER THAN A 24 HOUR 
PERIOD.  

TIP:

 

IT’S IMPORTANT TO FLUSH THE SYSTEM IN  

BETWEEN USE OR WHEN SWITCHING CHEMISTRY TO 
PREVENT RESIDUAL BUILD UP AND TO AVOID MIXING 
CHEMICALS. 

Changing Chemicals:

5. Maintenance & Cleaning 

The system is designed to minimize maintenance and cleaning.  

Tips: 

Clear the system at least once a day by spraying clean 
water through the system for at least ten seconds. 
Keep batteries charged. 
Inspect cable for cuts, tears or damage. 
Inspect applicator for debris or damage. 



Storage

Empty fluid or run until empty. 
Insert at least 1 inch (2.5cm) of clean water in the 
liquid tank. 
Run the electrostatic sprayer for at least 45-60  
seconds to flush active chemicals from the system. 
Remove batteries and re-charge by placing on the 
charger. 
Wipe down exterior with water or alcohol to remove 
dirt and soil. 
Use the power indicator on the end of the battery to 
determine the battery state of charge (5 bars = full 
charge). 
Insert battery covers back into battery compartment 
slots to prevent foreign particles and moisture from 
damaging battery contact connectors. 
Coil the quick connect electro-fluid cable up neatly 
and securely. 


To flush the system, empty the liquid tank and fill with 
at least 1 inch (2.5cm) of clean water.  
Spray for at least 45-60 seconds to flush the previous 
fluid from the system. 

Battery Removal

Make sure the system is powered off. 
Remove both battery covers by squeezing the  
triangular pop-out portion of the covers and pulling 
outwards. 
When covers are off, a pull-tab will be visible to assist 
in removal of the batteries. 
Place batteries into charger to fully charge for next 
usage. Each battery takes approximately 45 minutes 
to fully charge. 


CAUTION: 

DO NOT STORE THE SYSTEM IN AN AREA 

THAT MAY FREEZE (TO AVOID DAMAGE FROM LIQUID 
REMAINING IN THE SYSTEM AND LINES). THIS WILL 
VOID THE WARRANTY. 

CAUTION: 

TO PREVENT CROSS CONTAMINATION 

OF CHEMICALS, YOU MUST PERFORM A FLUSH 
ANY TIME YOU CHANGE THE TYPE OF CHEMICALS 
BEING USED. 

Flushing the Electrostatic Sprayer

Summary of Contents for EM360

















Reviews: