Emerson Vilter VSG Installation, Operation & Maintenance Manual Download

Page: 42 / 112

3 – 18

VSG/VSSG • Installation, Operation and Maintenance Manual •Vilter/Emerson • 35391STG

OIL

003

001

BLEED

DRAIN

002

BLEED

004

101

102

103

005

1000W

001

002

OIL CHARGE

002

COMPRESSOR

MOTOR

OIL COOLER

MOTOR

OIL PUMP

OIL FILTER

COALESCING OIL

RETURN LINE

PRESSURE

EQUALIZING LINE

SUCTION INLET

DISCHARGE OUTLET

OIL MIXING

VALVE

DRAIN

CLOSE

OPEN

OIL SEPARATOR

DRAIN

VENT

COOLING
WATER

DISCHARGE OUTLET

SUPPLY

RETURN

005

BLEED

004

BLEED

Figure 3-17. Priming Oil Cooler (Shell & Tube) and Piping

PRIMING COMPRESSOR AND OIL FILTERS

NOTE

Running the compressor oil pump at this point will
help lubricate the compressor bearings and shaft

seal surfaces.

(Reference Figure 3-18)

11. Open shut-off valve(s) (8) at oil

lter inlet(s).

12. Close oil bypass shut-off valve (5).
13. Open oil mixing valve (7) via control panel. In Manual

Mode, change “Manually Open (%)” value to “100”.

14. Run oil pump (6) for approximately 20 seconds only.
15. Stop oil pump (6) and wait for a minimum of 30 min-

utes. This will allow oil in the compressor (2) to drain
and oil level (9) in oil separator (3) to settle.

NOTE

Oil mixing valve can remain in Manual Mode since
the setpoint will change the mode to Auto when
reached. For further details, see PLC Compact Logix

manual.

16. Refer to Pre Start-Up Checklist and ensure all items

are ready prior to starting the compressor.

17. When ready, run compressor unit and allow it to

reach normal operating temperature.

18. Using a properly selected oil pump, connect oil

pump to suction oil charging valve (1). For suction
oil charging valve location, see Figure 3-16.

19. Open suction oil charging valve (1) and

ll oil separa-

tor (3) to Normal Operating Level.

20. Once the Normal Operating level has been reached,

shut off the oil pump and close the suction oil charg-
ing valve (1). Disconnect and remove oil pump.

Section 3 • Installation

Summary of Contents for Vilter VSG

















































































































Search results

Summary of Contents for Vilter VSG

Reviews:

Related manuals for Vilter VSG

Brands by name

Popular brands

Emerson Vilter VSG, Installation, Operation & Maintenance Manual

Search results

Summary of Contents for Vilter VSG

Reviews:

Related manuals for Vilter VSG

Brands by name

Popular brands