manualshive.com logo in svg

Emerson Rosemount Analytical RDO, Manual

Share
Download
Emerson Rosemount Analytical RDO Manual Download Page 8

8

MODEL RDO 

INSTALLATION

FIGURE 1-10. Attached plug (left) and attached dome connector (right)

Lock nut

Large o-ring

Port plug

Lock nut

Large o-ring

Dome connector

1.4 INSTALLING DOME CONNECTORS
AND PLUGS

Install dome connectors and plugs as shown in Figure
1-10.

1. Place the O-ring over the threaded end of the con-

nector or plug.

2. Screw the connector or plug into the opening until it

is snug. Then tighten an additional 1/2 turn. Do not
overtighten.

3. Place the lock nut concave side down on the

threads and using a screwdriver blade and mallet,
tighten the lock nut until there is approximately one
thread showing.

4. Thread cable through the dome connectors and

secure by tightening the nut to about 15 in-lbs of
torque. Confirm that cable does not slide or wiggle
after the nut has been tightened. Leave sufficient
cable inside the enclosure to make secure connec-
tions without placing stress on the cable.

Summary of Contents for Rosemount Analytical RDO

































Reviews:

No comments

Brands by name

Popular brands

Load more brands