Emerson Rosemount Analytical RDO Manual Download Page 29

Page: 29 / 32

MODEL RDO

SPECIFICATIONS

SECTION 8.0

SPECIFICATIONS

8.1 RDO PROBE

Wetted Materials:

Delrin

, ABS, Viton

, titanium, polycar-

bonate/poly(methyl methacrylate) blend

Dimensions:

length 8.0 in (203 mm) diameter 1.9 in

(47 mm)

Rating:

IP-67 with cap off; IP-68 with cap installed

Process connection:

1-1/4 inch FNPT

Integral cable length:

32 ft (10 m)

Maximum cable length (quick disconnect cable only):

4000 ft (1219 m)

Pressure:

up to 314 psig (2060 kPa abs)

Temperature:

32 to 122°F (0 - 50°C)

Range:

0 to 20 ppm (mg/L) or 0 to 200% saturation

Accuracy:

±0.1 ppm between 0 and 8 ppm; ±0.2 ppm

between 8 and 20 ppm

Resolution:

0.01 ppm (mg/L)

Digital output:

Modbus/RS485

Response time:

30 sec to 90% of final value; 37 sec to

95% of final value (at 25°C)

Operating life of sensing cap:

1 year from first reading

Shelf life of sensing cap:

2 years from date of manu-

facture; for full operating life install the sensing cap
within one year of manufacture date.

Safety directive:

73/23/EEC

EU directives:

2004/108/EC for Electro-

magnetic Compatibility (EMC) and
72/23/EEC for Safety

Immunity:

EN 61000-6-2, Electromagnetic Compatibility

(EMC) part 6-2

Emissions:

Class A requirements of CISPR 11:2004

8.2 RDO ANALYZER

Enclosure:

Polycarbonate, rated NEMA 4X, IP67

Dimensions (W x H x D):

6.3 x 6.3 x 3.6 in (16 x 16 x

9.0 cm)

Display:

liquid crystal; character height 0.4 in (6 mm)

Mounting:

suitable for pipe or wall mounting

Conduit openings:

six; PG 13.5 (

⁄

inch); three gland

fittings and five plugs ship with the analyzer

Ambient temperature and humidity:

-4 to 158°F (-20 to

70°C); 95% RH (non-condensing)

Power:

100 to 240 VAC, approximately 0.15 A, 50-60 Hz

Analog Outputs:

two fully scalable 4-20 mA outputs,

each loop-powered (9-36 VDC)

Digital Output:

Modbus/RS485

Relays:

two low voltage relays, <50 VAC or VDC, maxi-

mum current 2 A (resistive or inductive) two high
voltage relays, 264 VAC max, maximum current 5 A
(resistive or inductive)

Barometric pressure range:

8.86 to 29.53 in Hg (300 to

1000 mbar)

Barometric pressure accuracy:

±0.09 in Hg (±3 mbar)

EU directive:

2004/108/EC for Electromagnetic

Compatibility (EMC)

Immunity:

EN61000-6-2, Electromagnetic Compatibility

(EMC) part 6-2

Emissions:

EN61000-6-4 Electromagnetic Compatibility;

includes IEC/EN 61000-3-2 and IEC/EN61000-3-3,
where applicable

Safety:

UL 61010-1 and CAN/CSA C22.2 #61010-1

1 Delrin is a registered trademark of DuPont DeNemours, LLC
2 Viton is a registered trademark of DuPont Dow Elastomers, LLC

Summary of Contents for Rosemount Analytical RDO
































Search results

Summary of Contents for Rosemount Analytical RDO

Reviews:

Brands by name

Popular brands

Emerson Rosemount Analytical RDO, Manual

Search results

Summary of Contents for Rosemount Analytical RDO

Reviews:

Brands by name

Popular brands