background image

1. Open styrofoam unit containing fan. Remove upper

and center sections of styrofoam unit. Remove parts
and check to see that you have received the following:

a. One fan motor and housing assembly
b. One motor coupling cover
c. One ceiling cover
d. Five fan blades
e. Five blade holder caps (left)
f. Five blade holder caps (right)
g. One hanger ball/downrod assembly
h. One hanger bracket
i. One light kit adapter assembly
j. One light kit plate assembly
k. One light kit glass 
l. Two die cast light kit glass holders
m.One uplight lead assembly 
n. One loose parts bag containing:

1. One setscrew
2. One 5/32" hex wrench
3. One 3/16” hex wrench
4. Four 8-32 x 1-1/4” threaded studs
5. Four knurled knobs
6. Four lockwashers
7. Seven wire connectors
8. Three 8-32 x 3/8" phillips head screws
9. One hairpin clip

10. One clevis pin
11. Twenty-one 10-32 x 3/8" pan head screws
12. One flatwasher

This Manual Is Designed to Make it as Easy as Possible for You to

Assemble, Install, Operate and Maintain Your Ceiling Fan

Tools Needed for Assembly

One six-inch blade screwdriver

One stepladder

One Phillips head screwdriver

One wire stripper

Seven wire connectors(supplied.) 

MATERIALS

Wiring outlet box and box connectors must be of type
required by the local code. The minimum wire would
be a 3-conductor (2-wire with ground) of the wire size,
to right:

3

Installed Wire Length

Wire Size A.W.G.

Up to 50 ft.

14

50-100 ft.

12

Unpacking Instructions

For your convenience, check-off boxes are provided next to each step. As each step is completed, place a
check mark in the box. This will insure that all steps have been completed and will be helpful in finding
your place should you be interrupted.

BLADE HOLDER
CAPS (LEFT)

BLADE HOLDER
CAPS (RIGHT)

UPPER STYROFOAM
SECTION

CEILING
COVER

FAN BLADES

MOTOR
COUPLING
COVER

HANGER BALL/
DOWNROD
ASSEMBLY

HANGER 
BRACKET

LOOSE
PARTS
BAG

CENTER
STYROFOAM
SECTION

LIGHT KIT
PLATE
ASSEMBLY

LIGHT KIT
GLASS 

LIGHT KIT
ADAPTER
ASSEMBLY

LOWER 
STYROFOAM
SECTION

FAN MOTOR
AND HOUSING
ASSEMBLY

UPLIGHT
LEAD ASSEMBLY

DIE CAST
GLASS HOLDERS

If you feel you do not have enough wiring knowledge or
experience, have your fan installed by a licensed
electrician.

NOTE: Place the parts from the loose parts bags
in small containers to keep them from being lost.
If any parts are missing, contact your local
retailer or catalog outlet for replacement before
proceeding.

Do not install or use fan if any part is damaged or
missing. Call Toll-Free:

1-800-654-3545

This product is designed to use only those parts
supplied with this product and/or any accessories
designated specifically for use with this product by
Emerson Company. Substitution of parts or acces-
sories not designated for use with this product by
Emerson Company could result in personal injury or
property damage.

WARNING

!

WARNING

!

WARNING

!

Summary of Contents for ODYSSEY CF2454BQ02

















Reviews: