background image

www.Fisher.com

Fisher

 L2e Electric Level Controller

Contents

Introduction

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Scope of Manual

1

. . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Description

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Specifications

2

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Educational Services

2

. . . . . . . . . . . . . . . . . . . . . . . . .

Installation

4

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Attaching a Vertical Displacer

5

. . . . . . . . . . . . . . . . . .

Attaching a Horizontal Displacer

5

. . . . . . . . . . . . . . .

Attaching the Sensor to the Vessel

5

. . . . . . . . . . . . .

Electrical Connections

6

. . . . . . . . . . . . . . . . . . . . . . . .

Seal Certification

10

. . . . . . . . . . . . . . . . . . . . . . . .

L2e Initial Setup (Dry Displacer)

11

. . . . . . . . . . . . . . .

L2e Zero and Span Adjustment (Wet Displacer)

11

. .

Principle of Operation

12

. . . . . . . . . . . . . . . . . . . . . . . .

Maintenance

14

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Removing the Controller From the Sensor

14

. . . . . .

Installing Sensor Repair Kit (RL2SENSX012)

14

. . . . .

Replacing the Complete Controller 

Assembly (RL2E0X00C22)

15

. . . . . . . . . . . . . . . . .

Related Documents

16

. . . . . . . . . . . . . . . . . . . . . . . . . .

Parts Ordering

16

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

Figure 1. Fisher L2e Electric Level Controller

X0660

Introduction

Scope of Manual

This instruction manual includes installation, adjustment, maintenance, and parts ordering information for the Fisher
L2e electric liquid level controller.

Do not install, operate or maintain an L2e electric liquid level controller without being fully trained and
qualified in valve, actuator, and accessory installation, operation, and maintenance. 

To avoid personal

injury or property damage, it is important to carefully read, understand and follow all the contents of
this manual, including all safety cautions and warnings. 

If you have any questions about these

instructions, contact your 

Emerson sales office

 before proceeding.

Instruction Manual

D103531X012

L2e Controller

June 2022

Summary of Contents for Fisher L2e





















Reviews: