manualshive.com logo in svg

Emerson Fisher L2e, Instruction Manual

Share
Download
Emerson Fisher L2e Instruction Manual Download Page 11

Instruction Manual

D103531X012

L2e Controller

June 2022

11

L2e Initial Setup (Dry Displacer)

Refer to figure 7.

1.  Apply power to the L2e Switch assembly.

2.  Move Span to minimum setting.

3.  If the switch is already in the state that opens the dump valve, skip to step 4. Otherwise, (e.g., lever B is resting on

its travel stop), first move the plunger 

away

 from the switch by moving the Zero adjustment until the switch just

changes to the state required to open the dump valve.

4.  Slowly bring the plunger

 towards

 the switch by moving the Zero adjustment until the switch changes to the state

required to 

close

 the dump valve.

L2e Zero and Span Adjustment (Wet Displacer)

After initial setup (dry displacer) is complete,

1.  Enable process flow into the vessel.

2.  Move Zero and Span Adjustment for desired liquid zero position and level DG.

3.  Tighten the Zero Adjustment hex nut (key 5), shown in figure 10, to lock the Zero setting.

Figure 7. Initial Setup

ÂÂ

SPAN ADJUSTMENT

ZERO
ADJUSTMENT

SPAN 
ADJUSTMENT

ZERO 
ADJUSTMENT

CAUTION: FACTORY SET
— DO NOT ADJUST —

MOVE

MOVE

LEVEL HEIGHT

LEVEL

DIFFERENTIAL GAP

INCREASE

DECREASE

RAISE

LOWER

Summary of Contents for Fisher L2e





















Reviews:

No comments

Brands by name

Popular brands

Load more brands