manualshive.com logo in svg

Emerson Fisher L2e, Instruction Manual

Share
Download
Emerson Fisher L2e Instruction Manual Download Page 16

Instruction Manual

D103531X012

L2e Controller

June 2022

16

Related Documents

D

 Bulletin 34.2:L2e  Fisher L2e Electric Level Controller (

D103532X012

)

D

 Changing easy-Drive Electric Actuator On/Off Input Configuration from Single Dry Contact Control to Dual Dry

Contact Control—Supplement to L2e Electric Level Controller Instruction Manual (

D103987X012

)

D

 Converting a Threaded NPT Connection to a Flange Connection—Supplement to Fisher L2, L2e, and L2sj Liquid Level

Controller Instruction Manuals (

D103277X012

)

D

 Dimensions for NPS 2 CL150 through 1500 Slip On Flange Connections—Supplement to Fisher L2, L2e, and L2sj

Liquid Level Controller Instruction Manuals (

D103405X012

)

D

 Bulletin 51.2:D3 Fisher D3 Control Valve (

D103269X012

)

D

 Fisher D3 Control Valve with easy-Drive Electric Actuator Instruction Manual (

D103460X012

)

D

 Bulletin 51.2:D4 Fisher D4 Control Valve Assembly (

D103039X012

)

D

 Fisher D4 Control Valve with easy-Drive Electric Actuator Instruction Manual (

D103597X012

)

All documents are available from your 

Emerson sales office

 or Fisher.com.

Parts Ordering

When corresponding with your Emerson sales office about this equipment, always mention the serial number of the
controller. The serial number can be found on the nameplate.

  WARNING

Use only genuine Fisher replacement parts. Components that are not supplied by Emerson should not, under any
circumstances, be used in any Fisher instrument. Use of components not supplied by Emerson may void your warranty,
might adversely affect the performance of the valve, and could cause personal injury or property damage.

Kits

Description

Part Number

Sensor Repair Kit

Repair kit includes keys 74, 75, 76, 77, and 78
(fluorocarbon O‐rings, anti‐extrusion ring, 
retaining ring, and fluorocarbon backup ring)

RL2SENSX012

Description

Part Number

Controller Assembly Replacement

Replacement kit includes complete controller 
assembly (figure 11) with mounting screws
and gasket

RL2E0X00C22

Summary of Contents for Fisher L2e





















Reviews:

No comments

Brands by name

Popular brands

Load more brands