Emerson Fisher FLOBOSS 407 Instruction Manual Download Page 88 | Manualshive

Page: 88 / 200

background image

FloBoss 407 Instruction Manual

3-32

Rev 5/00

4.

If the analog output is unable to drive the field device to the 100% value, confirm the +V (1 to 5
volts) voltage is present at the field device.

♦

If the voltage is present and the device is not at the 100% position, the resistance value of the
device is too large for the +V voltage. A field device with a lower internal resistance should
be used.

♦

If the voltage is not present at the field device, but it is present at field wiring terminal B,
there is excessive resistance or a break in the field wiring.

3.5.3 Discrete Input Source Module

Equipment Required:

Jumper wire

Place a jumper across terminals B and C. The LED on the module should light and the status as read by
the ROCLINK software should change to “1”. With no jumper on terminals B and C, the LED should
not be lit and the status should be “0”. If the unit fails to operate, make sure a correct value for the
module resistor is being used.

3.5.4 Discrete Input Isolated Module

Equipment Required:

Voltage generator capable of generating 11 to 30 V dc
Personal Computer running ROCLINK Software

Supply an input voltage across terminals B and C. The LED on the module should light and the status
as read by the ROCLINK software should change to “1”. With no input on terminals B and C, the LED
should not be on and the status should be “0”. If the unit fails to operate, make sure a correct value for
the module resistor is being used.

«
...
86
87
88
89
90
...
»

Summary of Contents for Fisher FLOBOSS 407









































































































































































































Reviews:

No comments

Related manuals for Fisher FLOBOSS 407

Brand: ZETRON Pages: 3

Brand: Danfoss Pages: 24

Brand: EasyIO Pages: 18

Brand: Salda Pages: 20

Brand: Lamtec Pages: 136

Brand: Parker Pages: 30

Compax3M Series

Brand: Parker Pages: 52

Brand: Parker Pages: 337

Brand: Vaillant Pages: 27

Brand: Vaillant Pages: 36

Brand: Vaillant Pages: 28

Brand: Vaillant Pages: 92

Brand: WAREMA Pages: 4

Brand: Balboa Water Group Pages: 88

Brand: ABB Pages: 2

Brand: Mitsubishi Pages: 30

Brand: Ezodo Pages: 7

Brand: Samson Pages: 70

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands