Emerson Fisher FLOBOSS 407 Instruction Manual Download Page 175

Page: 175 / 200

FloBoss 407 Instruction Manual

Rev 5/00

B-19

B.8 SPECIFICATIONS

Remote MVS101 Specifications

DIFFERENTIAL PRESSURE INPUT

Range

: 0 – 322 inches H2O (0 – 80 kPa)

Reference Accuracy:

0.1% of span (includes

linearity, hysteresis, and repeatability effects), for
spans from 1:1 to 10:1 turndown.

STATIC PRESSURE INPUT

Range:

0 – 1450 psia (0 – 10,000 kPa abs.)

Reference Accuracy:

0.1% of span (includes

linearity, hysteresis, and repeatability effects), for
spans from 1:1 to 10:1 turndown.

PROCESS TEMPERATURE INPUT

Type:

For platinum 100-ohm RTD

(conforming to

IEC 751 Class B), with

= 0.00385.

Range:

-50 to 350 °C (-58 to 662 °F).

Reference Accuracy:

±0.1%, exclusive of RTD

sensor error. Specification includes linearity,
hysteresis, and repeatability effects.

OUTPUT

Type:

RS-485 asynchronous serial communication

using Fisher protocol.

Rate:

9600 baud.

POWER

20 mA dc max. at 7.5 to 27 Vdc, supplied by ROC or
FloBoss.

ENVIRONMENTAL

Operating Temperature:

-40 to 75 °C (-40 to 167 °F).

Storage Temperature:

-40 to 85 °C (-40 to 185 °F).

Operating Humidity:

5 to 100% relative humidity,

non-condensing.

DIMENSIONS

Overall:

4.0 in. H by 5.1 in. W by 7.2 in. D (102

mm by 130 mm by 183 mm).

Conduit Connections:

Electronics head has two

1/2-inch NPT connections for conduit.

Process Connections:

Sensor body has two 1/4-

18 NPT connections on 2 1/8-inch (54 mm)
centers.

CONSTRUCTION

Sensor Body:

316 SST. Silicon oil filled.

Diaphragm:

Hastelloy C (NACE compliant).

Electronics Head:

urethane-painted die-cast

aluminum alloy, rated Type 4X.

MOUNTING

For pipestand mounting, mounts on 2-inch pipe
using

optional mounting bracket

. Can also

mount to wall/panel on 2.8-inch centers using
5/16” bolts and optional mounting bracket.

WEIGHT

7 lb. (3 kg).

APPROVALS

Approved by CSA for hazardous locations Class I,
Divi sion 1 (explosion proof), Groups C and D.

Also approved by CSA to IEC standards for
Class I, Zone 1 (Flameproof), Group IIB.

Summary of Contents for Fisher FLOBOSS 407









































































































































































































Search results

Summary of Contents for Fisher FLOBOSS 407

Reviews:

Related manuals for Fisher FLOBOSS 407

Brands by name

Popular brands

Emerson Fisher FLOBOSS 407, Instruction Manual

Search results

Summary of Contents for Fisher FLOBOSS 407

Reviews:

Related manuals for Fisher FLOBOSS 407

Brands by name

Popular brands