background image

 

1592010400 PROG TOOL EN 19.03.2020                                    PROG TOOL                      

 

    2/8

 

 

 

 

1.  BEFORE USE 

 

Caution: avoid any contact of this equipment with rain or water, in order to 
prevent the development of flames or electric shock. 

 

Caution: do not remove the cover, in order to 
reduce the risk of electric shock. There are no 
components inside that need maintenance by 
the  user.  Always  refer  to  qualified  service 
staff for any intervention.

 

 

The  symbol  characterized  by  a  lightning  inside  an  equilateral  triangle  is 
intended  to  alert  the  user  of  a  non-insultated  voltage  souce  within  the 
product area that is sufficiently high to constitute a risk of electric shock to 
persons.

 

 

The  symbol  characterized  by  an  esclamation  mark  inside  an  equilateral 
triangle is intended to alert the user of important operating and maintenance 
(servicing) instructions.

 

 

CAUTION 

 

This  equipment  must  be  installed  only  by  the  service  staff  with  adequate 
technical  training  and  experience,  in  order  to  be  aware  of  any  possible 
danger. Operations described in this manual are intended to be for exclusive 
use of the service staff. The user is is not enabled to open the device. 

 

 

CAUTION 

 

Dixell Srl reserves the right to modify this user’s manual at any time without 
prior notice. The latest version available can be dowloaded from the website. 
 

 

 

CAUTION 

 

This  is  a  class  A  product.  In  residential  environments  it  can  cause  radio 
interference. In this case the user may need to take appropriate measures. 
 

 

 

CAUTION 

 

Dixell Srl reserves the right to change the components of its products, even 
without notice, ensuring the same and unchanged functionality. 
 

 

CAUTION 

 

Since Dixell products are part of a high-level technology, a qualification and 
a  configuration/programming/commissioning  stage  is  required  to  best  use 
them. Otherwise, these products may malfunction and Dixell cannot be held 
responsible. The product must not be used in any way that differs from that 
stipulated in the documentation. 
 

 

Summary of Contents for dixell









Reviews: