background image

AE4-1312 R2

© 2010 Emerson Climate Technologies

Printed in the U.S.A.

17

Model

Frame Size*

Charge Limit

120% x Limit **

Pounds

kg

Pounds

kg

ZR16-ZR29KC 

53 

2.7 

7.2 

3.24

ZR16-ZR24K4 

53 

2.7 

7.2 

3.24

ZR26-ZR48KC 

63 

3.6 

9.6 

4.32

ZR18-ZR48K3 

63 

3.6 

9.6 

4.32

ZR54-ZR81KC 

70 

10

 4.5 

12.0 

5.40

ZR54-ZR61K3 

70 

10

 4.5 

12.0 

5.40

ZR16-ZR34KA 

53 

3.6 

9.6 

4.32

ZR38-ZR54KA 

63 

10 

4.5 

12.0 

5.40

TANDEM 

63 

10 

4.5 

12.0 

5.40

TANDEM 

70 

12 

5.5 

14.4 

6.60

Table 5

Compressor Refrigerant Charge Limits

*Approximate Shell Diameter (e.g. 63 = 6.5 Inches)

** Charge Allowance for system

Table 6

Crankcase Heaters

Copeland

®

 Model

Frame 

Size

Emerson Part # Volts Watts

Tutco Part # Leads

ZR16KC/4 - ZR29KC/4 

ZR16KA - ZR34KA 

53 

018-0052-00 

240 

40 

02-6319-00 

21”

53 

018-0052-01 

120 

40 

02-6319-02 

21”

ZR18K3 - ZR48K3 

ZR26KC - ZR48KC 

ZR38KA - ZR54KA 

63

018-0041-00 

240 

40

02-6307-00

21”

63 

018-0041-01 

120 

40 

02-6307-02 

21”

63 

018-0041-02 

480 

40 

02-6307-03 

21”

63 

018-0041-03 

575 

40 

02-6307-06 

21”

63 

018-0041-04 

240 

40 

02-6311-00 

48”

63 

018-0041-05 

480

40 

02-6311-03 

48”

63 

018-0041-06 

240 

40 

02-6313-00 

32”

ZR54K3 - ZR61K3 

ZR54K3 - ZR81KC 

All 018-0057-XX 

Heaters fit both 63 and 

70 frame* shells 

70 

018-0057-00 

240 

70 

02-6332-00 

21”

70 

018-0057-01 

480 

70 

02-6332-03 

21”

70

018-0057-02 

575 

70 

02-6332-06

21”

63 & 70 

018-0057-03 

240 

70 

02-6334-00 

32” 

018-0057-04 

240 

70 

02-6335-00 

48”

018-0057-05 

480 

70 

02-6335-03 

48”

018-0057-06 

575 

70 

02-6335-06 

48”

018-0057-07 

120 

70 

02-6335-02 

48”

018-0057-08 

400 

70 

02-6335-12 

48”

018-0057-09 

277 

70 

02-6332-04 

21”

*Approximate Shell Diameter (e.g. 70 = 7.3 Inches)

Summary of Contents for Copeland Scroll ZR K3 Series



















Reviews: