Emerson Copeland EazyCool OLQ-24V-Nxx-TWD Series Application Manuallines Download Page 9

Page: 9 / 34

Safety

Instructions

Product

Description

Installat

Electrical

Connection

Starting up &

Operation

Maintenance

& Repair

Dismantling &

Disposal

Condensing Unit For Refrigeration Networks

The LRU collects liquid refrigerant from each condenser in a network. It has a single
liquid inlet and outlet line.

Receiver Depth / Width

Height

Dimensions

Liquid

Weight

Capacity

T/B

(holes)

Inlet diameter Outlet diameter Net/Gross

b x t,(ø mm)

ø (inch)

Liquid

Receiver

Unit

630 / 1250

720

680 x 580 (12)

1 5/8

1 3/8

120 / 142

Table 5:

Liquid receiver unit LRU

Receiver volume in litre also indicates the pump down capacity in kg (at 50°C Liquid

temperature) when the receiver is 95% filled – Receiver CE approved.

1/2’’–14 NPTF connection for relief valve. Maximum allowable working pressure -
MAWP 33 Bar

Fitting a pressure relief device according to standard EN378-2 is the
responsibility of the installer.

2.6.5 Electrical box: components

All electrical components are pre-wired into the panel.
This panel contains:

Compressor contactor(s)

Fuse

Terminal blocks

DIN rail mounted terminals

Electronic controller

Fan Speed controller

Alarm relays

2.6.6 Pressure switch

All single compressor Copeland EazyCool™ condensing units for refrigeration networks
are equipped with:

Single low pressure switch with automatic reset: ALCO PS1-W3A

Electronic Condensing Unit Controller with HP and LP pressure transmitters

All two-compressor Copeland EazyCool™ condensing units for Refrigeration Network are
equipped with:

Single low pressure switch with automatic reset: ALCO PS1-W3A

Two high pressure switches ALCO PS3-WF4-HNS

Electronic Condensing Unit Controller with HP and LP pressure transmitters

C6.1.4/0305/E

Part no: 3136433

Summary of Contents for Copeland EazyCool OLQ-24V-Nxx-TWD Series



































Search results

Summary of Contents for Copeland EazyCool OLQ-24V-Nxx-TWD Series

Reviews:

Related manuals for Copeland EazyCool OLQ-24V-Nxx-TWD Series

Brands by name

Popular brands

Emerson Copeland EazyCool OLQ-24V-Nxx-TWD Series, Application Manuallines

Search results

Summary of Contents for Copeland EazyCool OLQ-24V-Nxx-TWD Series

Reviews:

Related manuals for Copeland EazyCool OLQ-24V-Nxx-TWD Series

Brands by name

Popular brands