manualshive.com logo in svg

Emerson 4320, Instruction Manual, Page: 13 / 64

Share
Download
Emerson 4320 Instruction Manual Download Page 13

Instruction Manual

D103621X012

4320

January 2018

13

Note

Information regarding 4320 DD's for the Field Communicator is available at: 
http://www.emerson.com/en-us/catalog/ams-475-field-communicator

The above link is for the English website. Go to http://www.emerson.com/en-us/locale-chooser to access a specific country or
regional website.

2.  Obtain the Network ID and Join Key from the gateway via web interface. Go to 

Setup

 and select 

Networ

k. The

Network ID will be shown. Select Yes to see the Join Key.

3.  Open the cover of the 4320 and attach the Field Communicator leads to the 4320 HART terminals (see figure 5 

or 6).

4.  Select 

Online

, 

Overview

, and 

Join Device to Network 

to enter the network parameter settings (see figure 21 for the

Overview menu tree).

5.  Remove the leads from the 4320 and close the cover. Tighten the instrument cover screws to a torque of 5.6 

to 6.7 N•m (50 to 60 lbf•in).

6.  Install the 4320 on monitored equipment and/or verify the gateway.

Note

1410 gateway version 4.4.28 or later or 1420 gateway version 4.4.15 or later is required.

Using AMS Wireless Configurator or AMS Device Manager (Using a HART Modem)

1.  Verify that AMS has a device description (DD) loaded for the 4320 Device Revision 4 (DD Revision 1 or later).

Note

Information regarding 4320 DD's for the Field Communicator is available at: 
http://www.emerson.com/en-us/catalog/ams-475-field-communicator

The above link is for the English website. Go to http://www.emerson.com/en-us/locale-chooser to access a specific country or
regional website.

2.  Obtain the Network ID and Join Key from the gateway via web interface.

3.  Open the cover of the 4320 and attach the HART modem leads to the HART terminals (see figure 5 or 6).

4.  In AMS select the device that is connected to the HART modem.

5.  Go to 

Configure

, 

Guided Setup

, 

Wireless 

to configure network membership (see figure 7). Select 

Join Device to

Network 

and enter the network parameter settings.

Summary of Contents for 4320

































































Reviews:

No comments