manualshive.com logo in svg

Emerson 4320, Instruction Manual, Page: 29 / 64

Share
Download
Emerson 4320 Instruction Manual Download Page 29

Instruction Manual

D103621X012

4320

January 2018

29

Output (On/Off Control)

Access the Output menu by pressing the right button to access the STATUS menu, the left button (NEXT), and then
NEXT again.

In the OUTPUT menu you can view/change the device mode. Press SELECT to view the current device mode. Press the
left button to toggle the mode from OUT OF SERVICE to IN SERVICE or vice versa. Select NEXT when done. The next
display asks if you would like to toggle the valve. Push the left button (YES) to toggle the valve, press the right button
(NO) to return to the OUTPUT menu. Press SELECT to exit the local user interface. Press NEXT to return to the STATUS
menu.

Note

The valve set point can be toggled from the LUI only when the device is Out of Service.

The LUI may have a Clear Latch screen if the latch is enabled and active in the device.

Using the Field Communicator

Overview

Refer to figure 21 for the Overview menu tree.

Figure 21. Field Communicator Menu Tree—Overview

Online

1 Overview

2 Configure
3 Service Tools

Overview

1 Device Status
2 Comm Status
3 Mode
4 Primary Purpose Variable
5 Join Device to Network
6 Device Information

Device Information

1 Identification
2 Revisions
3 Radio
4 Local User Interface
5 Capabilities

Radio

1 MAC Address
2 Manufacturer
3 Device Type
4 Device Revision
5 Software Revision
6 Hardware Revision
7 Transmit Power

1

Field Communicator

1 Offline
2 Online
3 Frequency Device
4 Utility

Primary Purpose Variables

1 Valve Position
2 Switch State
3 Set Point
4 Update Rate

1‐4

1‐6-2

1-6

Revisions

1 Universal
2 Device
3 Firmware
4 Hardware
5 DD

Local User Interface

1 Calibration Locked Out
2 Override Locked Out
3 Mode Changed Locked Out
4 LUI Language

1‐6-3

1-6-4

NOTE:

  1     ITEM LABEL IS PROCESS (INSTEAD OF VALVE POSITION) WHEN PROCESS REPORTING (MONITORING OR SNAP-ACTING MODE ONLY).
  2     ITEM LABEL IS LATCHING SWITCH (INSTEAD OF SWITCH STATE) WHEN OPERATING MODE IS LATCHING (MONITORING OR SNAP-ACTING MODE ONLY).
  3     SET POINT IS NOT VISIBLE WITH MONITORING OPTION.
  4     ITEM LABEL IS SNAP COMMAND (INSTEAD OF SET POINT) FOR SNAP-ACTING MODE.
  5     OVERRIDE LOCKED OUT AND MODE CHANGED LOCKED OUT ARE NOT VISIBLE WITH MONITORING OPTION.

1

2

3

4

5

5

Capabilities

1 Device Profile
2 Installed Options
3 Total Burst Messages
4 Events Supported
5 Number Discrete Variables

1-6-5

Summary of Contents for 4320

































































Reviews:

No comments