Emerson 4320 Instruction Manual Download Page 14 | Manualshive

Page: 14 / 64

Emerson 4320 Instruction Manual Download Page 14

Instruction Manual

D103621X012

4320

January 2018

14

Figure 7. Wireless Setup

CONFIGURE

CONFIGURE PUBLISHING

GUIDED SETUP

JOIN DEVICE TO NETWORK

There are three burst messages that can be configured. Each can have its own content, one of five trigger modes, and
a range of update rates. Burst messages may be set to default values or tailored to your application in Configure
Publishing. Refer to Broadcast Information on page 33 for additional information on burst configuration.

6. Remove the leads from the 4320 and close the cover. Tighten the instrument cover screws to a torque of 5.6 to

6.7 N•m (50 to 60 lbf•in).

7. Install the 4320 on monitored equipment and/or verify the gateway.

Note

1410 gateway version 4.4.28 or later or 1420 gateway version 4.4.15 or later is required.

Hazardous Area Classifications and Special Instructions for “Safe Use” and
Installations in Hazardous Locations

Refer to the following instruction manual supplements for approval information.

D

CSA (C/US) Approval Information for Fisher 4320 Wireless Position Monitor (

D

ATEX Approval Information for Fisher 4320 Wireless Position Monitor (

)

D

IECEx Approval Information for Fisher 4320 Wireless Position Monitor (

)

All documents are available from your

Emerson sales office

or Local Business Partner or at www.Fisher.com. Contact

your Emerson sales office or Local Business Partner for all other approval/certification information.

«
...
12
13
14
15
16
...
»

Summary of Contents for 4320

































































Reviews:

No comments