background image

 

 

15 

 

 

Fig. 11. EMERALD device connection in FLUSHING mode 

1. EMERALD HOME 4 device over the sink; 2. Power supply (adapter); 3. A diverter on 

the crane with a regulator; 4. Tap water inlet fitting ; 5. The outlet fitting of purified water ; 6. 
Plug for connecting a power source; 7. A plug for connecting the power of the flushing de-
vice; 8. On / off button flushing device; 9. Tube for supplying tap water to the device (not used 
in the FLSHING mode) ; 10 Tube of the outlet of purified water from the device (not used in 
the FLUSHING mode ) ; 11. Kitchen sink; 12. Hose supply of a solution of citric acid from the 
flushing device to the device; 13. Flushing device Emerald ; 14 Hose for the exit of the citric 
acid solution from the device back into the flushing device.

 

 

Maintenance of the EMERALD device is carried out in accordance with the diagram on Fig. 11 
 

Preparation of citric acid washing solution. 

To carry out the flushing procedure for the EMERALD it is necessary to prepare 1 (one) liter of 

citric acid washing solution in the tank of the flushing device (Fig. 18 – “5”). The flushing solution of 
citric acid is prepared on the basis of 200 grams of the citric acid and a half liter of water. Citric acid 
crystals are recommended to be diluted in hot water but the flushing is carried out by the solution with 
temperature of 60-70 °C (not hotter!). 

Important! It is not allowed flushing the EMERALD by the citric acid solution over 70°С. 

This  may  damage  the  device!  Claims  in  this  case  will  not  be  accepted.  For  accurate 
determination  of  the  temperature  of  the  flushing  solution  you  are  requested  to  use  the 
temperature control instrument. 

Summary of Contents for Home 4




























Reviews: