EMC2 VNX VG2 Hardware Information Manual Download Page 7 | Manualshive

Page: 7 / 43

background image

6

EMC VNX VG2/VG8 Hardware Information Guide

VNX VG8 overview

• One to four of the following network I/O modules:

– Two-port 10-Gb/s optical; labeled 10 GbE v2 on the latch handle

– Two-port 10-Gb/s optical; labeled 10 GbE v3 on the latch handle

Note: The two-port 10-Gb/s optical I/O module requires VNX OE for file 7.1 or
later.

– Four-port 1-Gb/s copper; labeled 1 GbE on the latch handle

– Two-port 1-Gb/s copper plus two-port 1-Gb/s optical; labeled 1 GbE on the

latch handle

– Two-port 10-Gb/s RJ-45 Base-T iSCSI/IP; labeled 10 GbE Base-T on the latch

handle

Note: The two-port 10-Gb/s RJ-45 Base-T/IP I/O module requires VNX OE for
Block R35 and VNX OE for File version 7.1 or later.

• Two management modules per Data Mover enclosure

• Two power supply/cooling (fan) modules per CPU module

◆

One or two CallHome modems (with power-supply cable and serial modem cable)

◆

One or two 1U Control Stations. Each 1U Control Station consists of the following

features:

• Intel 2.0 GHz single core Celeron processor with 800-MHz front side bus (FSB) and

512 KB cache

• 2 GB of RAM

• One 250-GB SATA hard drive

• Two rear-mounted USB ports and one front-mounted USB port

• Four RJ-45 10Base-T/100Base-TX/1000Base-T network interface connectors

(located on the rear panel)

• Two integrated serial ports, one for laptop/console redirection and one for the

CallHome modem

• One DVD-ROM drive

◆

Any required cables including LAN cables, modem cables, serial DB-9 cable, and IPMI

cable.

◆

Mounting rails with hardware

◆

Front bezel with VNX VG2 badge

VNX VG8 overview

Contained in a standard 19-inch (48.3 cm) NEMA (National Electrical Manufacturers
Association) rackmount cabinet, the VNX VG8 gateway weighs about from 74.91 lb
(33.7 kg) to 243.6 lb (109 kg) depending on how many 1U Control Stations and I/O
modules are installed in the cabinet. With the 2U Data Mover enclosure having the widest
and deepest dimension within the cabinet, the VNX VG8 measures from 5.25 to

«
...
5
6
7
8
9
...
»

Summary of Contents for VNX VG2












































Reviews:

No comments

Related manuals for VNX VG2

Brand: D-Link Pages: 2

Brand: D-Link Pages: 59

Airspot DSA-3100

Brand: D-Link Pages: 70

Brand: Panasonic Pages: 72

Brand: Gardena Pages: 21

Brand: Chipkin Pages: 30

Brand: THOR Pages: 20

Brand: Cellio Pages: 9

Brand: SerVision Pages: 40

Brand: Dispel Pages: 17

ZyXEL ZyWALL 10W

Brand: ZyXEL Communications Pages: 2

Brand: Xorcom Pages: 7

SmartNode 5540 Series

Brand: Patton Pages: 73

Smart Wireless Gateway 1420

Brand: Emerson Pages: 96

Brand: Xtreme Pages: 2

Brand: Askey Pages: 61

Brand: Planet Pages: 8

Brand: Planet Pages: 16

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands