EMC2 VNX VG2 Hardware Information Manual Download Page 28 | Manualshive

Page: 28 / 43

background image

Component description

EMC VNX VG2/VG8 Hardware Information Guide

27

Figure 22 Example of LC-type connectors

Four-port 8-Gb/s FC I/O module

The four-port 8-Gb/s FC I/O module (labeled 8 GbE Fibre on the latch handle) comes with
four optical (fibre) ports, one power/fault LED, and a link/activity LED for each optical port,
as shown in

Figure 23 on page 28

. This I/O module can interface at speeds of 2, 4, and 8

Gb/s. The four-port 8-Gb/s FC I/O module uses the SFP+ transceiver module.

Note: For information about connecting the four-port 8-Gb/s FC I/O module to a Tape
Backup, refer to the chapter describing the “Optional tape backup device cables” in the

EMC VNX VG2/VG8 Gateway Configuration Setup Guide.

1

Orange cable

3

Rubber gasket (jacket), receive (RX)

2

Rubber gasket (jacket), send or

transmit (TX)

4

Ferrule (connector end to SFP+ module)

A

2

A

1

3

1

2

4

CNS-001102

«
...
26
27
28
29
30
...
»

Summary of Contents for VNX VG2












































Reviews:

No comments

Related manuals for VNX VG2

Brand: Vanguard Pages: 74

Brand: NeoGate Pages: 37

Brand: Vantron Pages: 52

Brand: Grandstream Networks Pages: 20

SR6602-I AI Series

Brand: H3C Pages: 29

Brand: NETGEAR Pages: 7

Brand: Handlink Technologies Pages: 60

ZyWALL USG 2000

Brand: ZyXEL Communications Pages: 120

Brand: Gree Pages: 21

Brand: 2N Pages: 113

Brand: Avaya Pages: 30

Brand: Avaya Pages: 72

OmniAccess 8550

Brand: Alcatel-Lucent Pages: 98

Brand: Entone Pages: 5

Brand: Eelectron Pages: 9

Brand: ICPDAS Pages: 52

Brand: Cooper Atkins Pages: 21

Brand: 2N Pages: 9

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands