EMC2 VNX VG2 Hardware Information Manual Download Page 10

Page: 10 / 43

VNX VG8 overview

EMC VNX VG2/VG8 Hardware Information Guide

• One Fibre Channel (FC) I/O module (in slot 0) or one Fibre Channel over Ethernet

(FCoE) I/O module (in slot 0) SAN:

Note: The FCoE I/O module can replace the FC I/O modules in a factory-shipped
system if desired.

– Four-port 8-Gb/s optical (default, running at 2, 4, or 8 Gb/s); labeled 8 GbE

Fibre on the latch handle

– Two-port 10-Gb/s Fibre Channel over Ethernet (FCoE); labeled 10 GbE/FCoE on

the latch handle

Note: The two-port 10-Gb/s FCoE I/O module requires VNX OE for File version
7.0.35.3 or later.

• One to four of the following network I/O modules:

– Two-port 10-Gb/s optical; labeled 10 GbE v2 on the latch handle

– Two-port 10-Gb/s optical; labeled 10 GbE v3 on the latch handle

Note: The two-port 10-Gb/s optical I/O module requires VNX OE for File 7.1 or
later.

– Four-port 1-Gb/s copper; labeled 1 GbE on the latch handle

– Two-port 1-Gb/s copper plus two-port 1-Gb/s optical; labeled 1 GbE on the

latch handle

– Two-port 10-Gb/s RJ-45 Base-T iSCSI/IP; labeled 10 GbE Base-T on the latch

handle

Note: The two-port 10-Gb/s RJ-45 Base-T/IP I/O module requires VNX OE for
Block R35 and VNX OE for File version 7.1 or later.

• Two management modules per Data Mover enclosure

• Two power supply/cooling (fan) modules per CPU module

◆

One or two CallHome modems (with power-supply cable and serial modem cable)

◆

One or two 1U Control Stations. Each 1U Control Station consists of the following

features:

• Intel 2.0 GHz single core Celeron processor with 800-MHz front side bus (FSB) and

512 KB cache

• 2 GB of RAM

• One 250-GB SATA hard drive

• Two rear-mounted USB ports and one front-mounted USB port

• Four RJ-45 10Base-T/100Base-TX/1000Base-T network interface connectors

(located on the rear panel)

• Two integrated serial ports, one for laptop/console redirection and one for the

CallHome modem

• One DVD-ROM drive

Summary of Contents for VNX VG2












































Search results

Summary of Contents for VNX VG2

Reviews:

Related manuals for VNX VG2

Brands by name

Popular brands

EMC2 VNX VG2, Hardware Information Manual

Search results

Summary of Contents for VNX VG2

Reviews:

Related manuals for VNX VG2

Brands by name

Popular brands