Embertec Emberstrip ESUSAV8-ET-10D User Manual Download Page 20

 

 

 

For how long?

 

This warranty runs for the lifetime of the Embertec Emberstrip®. The lifetime of the 

Embertec Emberstrip® is 15 years from the date of purchase.

 

What will we do if connected equipment is damaged during the limited connected 
equipment warranty period and this warranty applies?

 

Subject to the limitations set forth in this warranty, we will elect (at our option) to repair or 

replace any equipment damaged by an Occurrence, or to pay you an amount equal to the 

replacement value for such equipment, not to exceed the overall maximum set forth below. 

In connection with the foregoing, we reserve the right to examine the damaged equipment 

at the site where the damage occurred. If we elect to replace the equipment and it has 

been discontinued, we will replace it with similar equipment of equal or greater value, 

subject to the overall maximum set forth below. We will pay for all shipping costs incurred 

in connection with the delivery of any repaired or replacement equipment to you, subject 

to the overall maximum set forth below.

 

What does this limited connected equipment warranty not cover?

 

This limited connected equipment warranty does not cover:

 

 

Any damage to connected equipment caused by improper use of the Embertec Emberstrip® 

or the connected equipment, accidents, acts of God (such as lightning strikes, floods or 

earthquakes), or normal wear and tear of the Embertec Emberstrip® or the connected 

equipment. For purposes of this warranty, 

“improper use” means not installing or 

operating the Embertec Emberstrip® in accordance with the manual, or not installing or 

operating the connected equipment in accordance with its manual.

 

 

Any damage to equipment that is not properly connected to an Embertec Emberstrip®, 

or damage to equipment connected to an Embertec Emberstrip® that is not properly 

connected to an AC power line with a protective ground.

 

 

Any damage to equipment connected to an Embertec Emberstrip® that had previously 

experienced another Occurrence. After each Occurrence, the Embertec Emberstrip® 

must be replaced.

 

 

Any damaged equipment that has been disposed before we have examined the 

equipment at the site where the damage occurred (or notified you that we would not be 

visiting the site), and elected whether to repair or replace it or pay for its replacement 

value, all in accordance with the terms set forth above.

 

 

Any damage to satellite dishes.

 

THE MAXIMUM CUMULATIVE AMOUNT WE WILL PAY FOR ALL 
REPAIRS, REPLACEMENT AND SHIPPING COSTS FOR  ANY  AND 
ALL DAMAGED EQUIPMENT QUALIFYING UNDER THIS WARRANTY

 

SHALL NOT EXCEED TWENTY FIVE THOUSAND DOLLARS ($25,000).

 

Any incidental, consequential, special or other indirect damages are not recoverable 

under this warranty. Some states do not allow the exclusion of incidental or consequential 

damages, so the foregoing limitation may not apply to you.

 

If the connected equipment is covered by an applicable 

homeowner’s

 or 

renter’s

 insurance 

policy, we reserve the right to be subrogated under such policy. In addition, this warranty 

shall not apply to any damaged equipment covered under the 

manufacturer’s

 warranty.

 

How do you file a claim under this limited connected equipment warranty?

 

To file a claim for connected equipment qualifying under this warranty, visit embertec.com

 

or call 1-800-838-9659 and provide a full description of the damage.

 

This warranty gives you specific legal rights. You may also have other rights which vary 

from state to state.

 

 

18

 

Summary of Contents for Emberstrip ESUSAV8-ET-10D






















Reviews: