manualshive.com logo in svg

Embedded Data Systems MN-RTD4W-H, Manual

Share
Download
Embedded Data Systems MN-RTD4W-H Manual Download Page 10

 

© 2020 Embedded Data Systems, LLC.; 2019 Fortune Drive; Lawrenceburg, KY 40342; Phone/Fax 502-859-5490     10 / 10 

EN-USERMAN MN-RTD4W-H V1.0  10.09.2020 

Regulatory Compliance 

FEDERAL COMMUNICATIONS COMMISSION (FCC) COMPLIANCE STATEMENT 

This device complies with part 15 of the FCC Rules. Operation is subject to the following two 
conditions: (1) This device may not cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause undesired operation. 
 
 

INDUSTRY CANADA (IC) COMPLIANCE STATEMENT 

This Class B digital apparatus complies with Canadian ICES-003.  
Cet appareil numérique de la classe B est conforme à la norme NMB-003 du Canada. 
 
 
 

EUROPEAN COMMUNITY (EC) DIRECTIVES CONFORMITY 

APPLICATION OF COUNCIL DIRECTIVE 2004/108/EC Standard to which Conformity is Declared: 
 

 

EN 61326-1:2006    

 

 

(Emmissions) 

 

 

EN 61326-2-3:2006  

 

 

(Immunity) 

 

 

EN 61000-3-2:2006+A1:2009+A2:2009  (Harmonics) 

 

 

EN 61000-3-3:2008  

 

 

(Flicker) 

 

 

 

 

 

 

 
Caution: The manufacturer is not responsible for any radio or television interference caused by using 
other than recommended cables or by unauthorized changes or modifications to this equipment. 
Unauthorized changes or modifications could void the user’s authority to operate this equipment. 

 

Summary of Contents for MN-RTD4W-H











Reviews:

No comments

Brands by name

Popular brands

Load more brands