manualshive.com logo in svg

emazys Z200, User Manual, Page: 7 / 41

Share
Download
emazys Z200 User Manual Download Page 7

Z200 PV Analyzer

User Manual

3

Unpacking and commissioning

3.1

Scope of delivery

The

PV Analyzer Z200

is delivered in a cardboard box.

INFORMATION.

If you use knives or sharp objects when unpacking, please
observe great care.

After unpacking, make sure that you have received all parts ordered. Accessories and special

items may have been ordered as well, so please check with your purchase order and invoice,
that nothing is missing. If you have not received all parts, please contact EmaZys or your local
distributor.

Z200 PV Analyzer std. kit.

1. Z200 PV Analyzer

2. Tone pickup

3. RRC2054 Battery

4. RRC-SMB-MBC Standard Battery Charger

5. Banana-MC4 PV+ testing lead

6. Banana-MC4 PV- testing lead

7. Banana Croc. GND testing lead

Note:

The picture shows the std. Z200 PV Analyzer testing kit. A range of different acces-

sories can be supplied from EmaZys - please go to EmaZys.com and see what we can offer. We
recommend to also buy and use the tone pickup, when ordering the Z200 PV Analyzer kit. The
tone pickup will enable more fault localisation functionality in your instrument.

4

Summary of Contents for Z200










































Reviews:

No comments