manualshive.com logo in svg

emazys Z200, User Manual, Page: 16 / 41

Share
Download
emazys Z200 User Manual Download Page 16

Z200 PV Analyzer

User Manual

Figure 3: An illustration showing the different options for choice of controller device for the

Z200

PV Analyzer

. The controller device may be a smartphone, a tablet computer, a PC / MAC or even

other unconventional devices.

Please note that using other browsers, such as e.g. Microsoft Internet explorer, is not recom-
mended and full functionality can not be guaranteed in such cases.

5.3.2

Appearance of main Graphical User Interface - GUI

Below we see screenshots of the main Graphical User Interface (GUI). The GUI is basically a sim-
ple website, hosted on the

Z200 PV Analyzer

.

Main menu User Interface.

This

screen will appear in your browser
window when connected with the
Z200 WiFi hotspot.
1) The

Main

button leads back to

this main GUI screen from any
other page in the controller inter-
face.
2) The charging state of the battery
is seen in the upper middle part of
the GUI. In this example we have 44

%

capacity left.

3) Press the red question mark at
any page in the controller interface,
to read a brief summary of the cho-
sen application.

13

Summary of Contents for Z200










































Reviews:

No comments