manualshive.com logo in svg

emazys Z200, User Manual, Page: 15 / 41

Share
Download
emazys Z200 User Manual Download Page 15

Z200 PV Analyzer

User Manual

INSTRUCTION

At the following URL youtube.com/EmaZys a number of in-
structional videos can be found. Also, EmaZys.com is frequently
updated with relevant technical guidance.

Figure 2: Once the Z200 is correctly connected to the string of photovoltaic modules, it can per-
form full string analysis controlled from the WiFi connected device.

NOTICE.

1. If the Z200 has been disconnected or turned off, you need

to reconnect to the Z200 hotspot.

2. If you get out of reach of the Z200, it may also be necessary

to reconnect your device with the Z200, depending on the
availability of other nearby networks within reach of your
device.

5.3

Requirements for controller devices

The controller device may be a smartphone, a tablet computer or a PC / MAC. It is left to the user
to choose his preferred device. In some situations a smartphone may be sufficient, and in other
cases when evaluating data, a device with a larger screen may be preferred.

5.3.1

Recommended internet browsers for controller devices

Z200 PV Analyzer

has been optimized for use with the following internet browsers.

Google Chrome browser

Apple Safari browser

Firefox browser

12

Summary of Contents for Z200










































Reviews:

No comments