manualshive.com logo in svg

emazys Z200, User Manual, Page: 13 / 41

Share
Download
emazys Z200 User Manual Download Page 13

Z200 PV Analyzer

User Manual

5.1

Front panel elements

In the illustrations below, you will find a description of each element found on the front panel
of the

Z200 PV Analyzer

. The tables below show sections of the front panel seen in Figure 1.

Figure 1: The Z200 PV Analyzer front panel.

The operating state of the instrument is indicated by 3 colored
light emitting diodes (LEDs). The green diode is on when the in-
strument is turned on. The yellow diode indicates that the WiFi
antenna is ready to transmit and receive data. The red LED will in
general blink when the instrument is busy with either measure-
ments or analysis

Placed on the middle of the front panel we find the ON/OFF
switch. When the instrument is turned on a small LED in the but-
ton will emit green light. The ON/OFF button also controls the
”Timer” application. This application is described in detail in the
Timer section.
The instrument USB antenna is found above the ON/OFF but-
ton.

Please never remove this antenna. It is paired to the

instrument, and EmaZys support is needed to install a new
antenna

.

The ON/OFF button is in the

OFF

state, and the instrument is

turned off.

10

Summary of Contents for Z200










































Reviews:

No comments