eLutions iR1600 Configuration Manual Download

Page: 23 / 76

Remote Configuration Guide

elutions.com

The following table describes the parameters and values that are displayed on this section of the iR1600 Remote Configuration screen.

Parameter

Description

Serial Number

This is the serial number assigned to the modem.

Hardware Part Number

This is the part number of the modem. The iR1600 GPS-Enabled modem is part
number 6000-CF-RFM and the Non-GPS part number is 6100-C5-RFM.

Hardware Revision

This value indicates the number of times the hardware was revised for the modem.

Application Part Number

This is the part number of the Remote Configuration toolkit.

Application Revision

This is the number of times the Remote Configuration toolkit has been revised.

Application Date

This is the date that the Remote Configuration was updated.

Application Info

This is the information regarding the specific application which the modem is
connected. This field may typically display the application’s version number, date,
etc.

Boot Part Number

This is the part number for the boot used for the remote modem.

Boot Revision

This is the number of times the boot has been revised.

I/O Expansion Part Number

This is the part number for the input/output expansion that was used for this
modem.

I/O Expansion Revision

This is number of times the input/output expansion part was revised for this
modem.

Summary of Contents for iR1600













































































Search results

Summary of Contents for iR1600

Reviews:

Related manuals for iR1600

Brands by name

Popular brands

eLutions iR1600, Configuration Manual

Search results

Summary of Contents for iR1600

Reviews:

Related manuals for iR1600

Brands by name

Popular brands