background image

www.eltherm.com

www.eltherm.com

MESSAGES

Error messages

In the event of an error, the display shows an error code. Sen-
sor errors are displayed with a delay of approx. 10 seconds.

Error codes

• E01 = AE1: Sensor short circuit (Pt100 only) 
   

        or temperature < -60°C

• E02 = AE1: sensor interruption
• E03 = AE1: 3rd wire missing or R ≥ 10Ω (thermocouple only),
• E04 = AE2: Sensor short circuit (only Pt100) 
   

        or temperature < -60°C

• E05 = AE2: sensor interruption
• E06 = AE2: 3rd wire missing or R ≥ 10Ω (thermocouple only)
• E07 = AE3: short circuit current/voltage input, interruption 
current/voltage input
• E08 = AE4: short circuit current/voltage input, interruption 
current/voltage input
• E09 = Hybrid relay open error
• E10 = Error hybrid relay short circuit.
• E11 = limiter active
• E12 = no mains supply (heating)
• E19 = internal error

Warning codes

• C00 = Protected parameter Code entry required (Set "C42" 
with the arrow keys „ /  “ „C42“ and confirm with "P".)

• AL1 = over/under temperature input 1
• AL2 = over/under temperature input 2
• AL3 = Alarm current monitoring output, load current < 0.3A

• SP2 = second set value via digital input active
• oFF = external controller release -> device blocked

Ramp status messages

• rF0 = ramp ended correctly
• rF1 = ramp aborted and ramped down in a controlled man-
ner
• rF2 = band alarm occurred during operation
• rF3 = ramp aborted
The ramp status is indicated by a flashing display alternating 
with parameter "P01" (3 seconds "P01", 1 second "rFx"). You 
can return to the normal display by pressing the "P" key.

PARAMETERS AND THEIR MEANING

The factory settings are specified in [..].

Parameter

meaning and range

P01

Input variable X1

Display only, resolution: °C

P02

Input variable X2

Display only, resolution: °C

P03

Reference variable

Display only, resolution: °C

P04

Current display

Only display, resolution: 0.1A

P05

Output level on the propor-

tional controller / continuous 

controller

Only display, resolution: %

P06

Time unit on the proportional 

controller

Display only, resolution: sec.

P07

Display of the current

Ramp phase

Display only, resolution: 
without unit

P08

Display of the remaining time 

of the current ramp phase / 

PWM phase

Display only, resolution: 0.1 
min.

P10

Control setpoint W1 [°C]

Range P13...P14, [5°C]

P11

Switching hysteresis

Range 0...10K, [2K]

P12

min standstill time hybrid

Relay range 0...30 min, 
[0 min], resolution: 0.1 min

P13

Highest settable setpoint 1

Range P14...950°C, [950°C]

P14

Smallest adjustable setpoint 1

Range -50°C...P13, [-50°C]

P15

Sensor correction X1

Range -30...10K, [0K]

P16

Overtemperature alarm 1

Range P17...999°C, [999°C]

P17

Low temperature alarm 1

Range -99°C...P16, [-99°C]

P18

Lower analog scaling value 

(0/2V, 0/4mA)

Range -50°C...P19, [0°C]

Summary of Contents for ELTC-MV2





























Reviews: