ELTEX RG-5421G-Wac User Manual Download Page 14

Page: 14 / 147

___________________________________________________________________________________

14 RG-5400 Subscriber router

2.6

Design

RG-5421G-Wac subscriber router enclosed into 187x124x32 mm plastic housing.

2.6.1

The device front panel

Fig. 4 shows front panel layout of RG-5421G-Wac device.

Fig. 4 –RG-5421G-Wac front panel layout

Light indicators are located on the front panel of RG-5421G-Wac, Table 3.

Table 3 – Description of indicators on the front panel

Front panel element

Description

Power

Indicator of power supply and the device operation status

WAN

WAN interface indicator

USB

Operation indicator of external USB devices (USB flash, external hard drive, 3G/4G
USB modem)

WiFi 2.4

Operation indicator for wireless network (frequency range is 2.4 GHz)

WiFi 5

Operation indicator for wireless network (frequency range is 5 GHz)

Phone

Analogue phone operation indicator

LAN

LAN interface port indicator

2.6.2

Rear panel of the device

The rear panel layout of RG-5421G-Wac device is depicted in Fig. 5.

Summary of Contents for RG-5421G-Wac




















































































































































Search results

Summary of Contents for RG-5421G-Wac

Reviews:

Related manuals for RG-5421G-Wac

Brands by name

Popular brands

ELTEX RG-5421G-Wac, User Manual

Search results

Summary of Contents for RG-5421G-Wac

Reviews:

Related manuals for RG-5421G-Wac

Brands by name

Popular brands