ELTEX RG-5421G-Wac User Manual Download Page 108

Page: 108 / 147

___________________________________________________________________________________

108 RG-5400 Subscriber router

Firmware update check function requires Internet access.

You may update the device firmware manually by downloading the firmware file from the web site

http://eltex.nsk.ru/downloads

and saving it on the computer. To do this, click the 'Select file' button in the

'Firmware image'

field, and specify path to firmware .tar.gz format file.

To launch the update process, click 'Upload file' button. The process may take several minutes (its

current status will be shown on the page). The device will be automatically rebooted when the update is
completed.

Do not switch off or reboot the device during the firmware update. If it can not be
avoided and uploading firmware image was recorded partly gateway will try to
launch backup firmware image (if it is available).

3.7.7.7

‘Reboot’ submenu

In the 'Reboot' submenu, you may reboot the device.

Click the 'Reboot' button to reboot the device. Device reboot process takes approximately 1 minute to

complete.

Summary of Contents for RG-5421G-Wac




















































































































































Search results

Summary of Contents for RG-5421G-Wac

Reviews:

Related manuals for RG-5421G-Wac

Brands by name

Popular brands

ELTEX RG-5421G-Wac, User Manual

Search results

Summary of Contents for RG-5421G-Wac

Reviews:

Related manuals for RG-5421G-Wac

Brands by name

Popular brands