Elterm redline asbill, Operating And Assembly Manual

Page: 5 / 12

5
Elterm M.M.Kaszuba Sp.J., ul. Przemyslowa 5, 86-200 Chelmno
Terminal A – use to connect voltage free room temperature
controller
Terminal B – use to connect temperature sensor 1 to boiler’s
body – central heating function (CH)
Terminal C - use to connect temperature sensor 2 to hot
water tank equipped with coil – hot utility water (HUW)
LED display, signaling system and control
Boiler
power
Manual power
distribution (%)
Power
modulation
Power supply
230/400V
Safety
fuses (A)
Power cord
(mm²)
Heated area A
(m²)*
Heated area B
(m²)**
4 kW 100 – 67 – 33 by 1/3 1 phase 1 x 20 3 x 2,5 ~ 50 ~ 70
4 kW 100 – 67 – 33 by 1/3 3 phases 3 x 6 5 x 1,5 ~ 50 ~ 70
6 kW 100 – 67 – 33 by 1/3 1 phase 1 x 32 3 x 4,0 ~ 70 ~ 100
6 kW 100 – 67 – 33 by 1/3 3 phases 3 x 10 5 x 2,5 ~ 70 ~ 100
9 kW 100 – 67 – 33 by 1/3 1 phase 1 x 40 3 x 10,0 ~ 110 ~ 150
9 kW 100 – 67 – 33 by 1/3 3 phases 3 x 16 5 x 2,5 ~ 110 ~ 150
12 kW 100 – 67 – 33 by 1/3 1 phase 1 x 63 3 x 10,0 ~ 150 ~ 210
12 kW 100 – 67 – 33 by 1/3 3 phases 3 x 20 5 x 4,0 ~ 150 ~ 210
15 kW 100 – 67 – 33 by 1/6 1 phase 1 x 80 3 x 10,0 ~ 180 ~ 250
15 kW 100 – 67 – 33 by 1/6 3 phases 3 x 25 5 x 4,0 ~ 180 ~ 250
18 kW 100 – 67 – 33 by 1/6 3 phases 3 x 32 5 x 6,0 ~ 220 ~ 310
21 kW 100 – 67 – 33 by 1/6 3 phases 3 x 40 5 x 6,0 ~ 260 ~ 360
24 kW 100 – 67 – 33 by 1/6 3 phases 3 x 40 5 x 10,0 ~ 300 ~ 400
27 kW 100 – 67 – 33 by 1/6 3 phases 3 x 50 5 x 16,0 ~ 220 - 380
30 kW 100 – 67 – 33 by 1/6 3 phases 3 x 50 5 x 16,0 ~ 240 - 400
33 kW 100 – 67 – 33 by 1/6 3 phases 3 x 50 5 x 16,0 ~ 260 - 450
36 kW 100 – 67 – 33 by 1/6 3 phases 3 x 63 5 x 16,0 ~ 280 - 480
39 kW 100 – 67 – 33 by 1/6 3 phases 3 x 80 5 x 25,0 ~ 290 - 500
42 kW 100 – 67 – 33 by 1/6 3 phases 3 x 80 5 x 25,0 ~ 300 - 520
45 kW 100 – 67 – 33 by 1/6 3 phases 3 x 80 5 x 25,0 ~ 320 - 570
48 kW 100 – 67 – 33 by 1/6 3 phases 3 x 80 5 x 25,0 ~ 340 - 600
* Heated area A – boiler as main source of heat ** Heated area B – boiler as alternative source of heat
Exact cable cross section must be matched by qualified electrician based on local conditions analysis.
1. LED display
2. CH operation diode (AsD)
3. HUW operation diode (AsD)
4. OK/ON/OFF button
5. LEFT – change button
6. DOWN – decrease value
8. Diode – °C
9. Diode – power distribution
10. Diode – operating time
11. UP – increase value
12. ON green diode
13. RIGHT – change button
14. OFF red diode