Elmo SUV-CAM BWV Instruction Manual Download

Page: 58 / 66

Troubleshooting

■

Battery and power source

Symptom Cause

Remedy

The SUV-Cam cannot be
turned ON.

Does the battery have a charge?

Use the attached AC adapter or charge the battery. (

P20)

Is the power in supply?

Use the attached AC adapter or the charged battery.

The battery runs out
quickly after charging.

The SUV-Cam is being used in a cold Climate

If the recorder is used in cold climates, the battery power may be
lowered temporarily. Warm up the recorder with your body
temperature or the like.

The power supply is ON
but the LCD display is
OFF.

Does the battery have a charge?

Use the supplied AC adapter or charge the battery. (

P20)

Is the power in supply?

Use the attached AC adapter or the charged battery.

Is the power saving mode ON?

Press any button to release the power saving mode.

Is the AV cable plugged in?

If the AV cable is plugged in, the video output is switched
automatically to the external monitor.
To confirm on the LCD monitor, unplug the AV cable.

Summary of Contents for SUV-CAM BWV



































































Search results

Summary of Contents for SUV-CAM BWV

Reviews:

Related manuals for SUV-CAM BWV

Brands by name

Popular brands

Elmo SUV-CAM BWV, Instruction Manual

Search results

Summary of Contents for SUV-CAM BWV

Reviews:

Related manuals for SUV-CAM BWV

Brands by name

Popular brands