background image

 

 

Technical Support: +44(0)23 9269 6638 (option 3)             PAK200546-CHUBB_02DC   Feb 2021 

©2021 ELMDENE INTERNATIONAL LTD  

 

M

AINTENANCE

   

 

Maintenance 

This unit is intended for use by Service Personnel only.  There are NO USER SERVICEABLE parts inside. 
 
There is no regular maintenance required of the PSU other than periodic testing, and replacement of the 
standby battery.  

Reference should be made to the battery manufacturer's documentation to determine 

typical/expected battery life with a view to periodic replacement of the battery.  

 

D

IAGNOSTICS

 

 

 
Local Diagnostics 

Green LED 

On = Mains Present 

Red LED 

Fault Diagnostics according to table: 

 

Red LED 

(fault) 

Green LED 

(mains) 

Status 

OFF 

ON 

Normal:

  Battery fully charged 

One short flash 

every second 

ON 

Normal:

  Battery charging but not fully charged 

Flashing: 

1second On 

1 second Off 

ON 

Fault:

  Output fuse or battery fuse blown, or 

battery/PSU fault 

OFF 

Fault:

  No mains, output fuse blown 

One short flash 

every 3 seconds 

OFF 

Fault:

  No mains, battery supplying load. 

OFF 

OFF 

Fault:

  No mains, No output, battery disconnected 

or completely discharged 

 

 

C

OMPLIANCE

 

 

 
This power supply unit meets the essential requirements of the following EU Directives: 
 
 

EMC: 

2014/30/EU 

Low Voltage: 

2014/35/EU 

WEEE: 

2012/19/EU 

 
This product is suitable for use in systems designed to comply with 

PD6662:2017 at Grade 3 and Environmental Class II 

 
EN50131-6:2017  

 

Type A Security Grade 3 

 

 

 

Environmental Class II  

 

Certification Body: 

 

Telefication B.V. 

Edisonstraat 12A 
Zevenaar, 6902 PK 
The Netherlands 
+31 (0) 316 - 583 180 

http://www.telefication.com

 

Summary of Contents for 20182423N









Reviews: