DS80MM1E-001C
5
T
T
e
e
s
s
t
t
m
m
o
o
d
d
e
e
The contact can be set to Test mode for 3 minutes by pressing the Test button on the front cover once. The LED lights up
whenever the contact is activated in Test mode. Whenever the Test button is pressed, the contact transmits a signal to
the control unit to test the wireless range and re-activates Test mode again for three minutes.
Test mode will end
automatically after 3 minutes and will return to normal operating mode.
L
L
e
e
a
a
r
r
n
n
i
i
n
n
g
g
p
p
r
r
o
o
c
c
e
e
d
d
u
u
r
r
e
e
Step 1: Remove the battery insulation.
Step 2: Start the learning function on the control unit; see the control unit manual for more information.
Step 3: Press the Test button on the contact to send a signal to the control unit.
Step 4: If the control unit receives the signal correctly will respond by emitting beeps. Refer to the manual of the control
unit to complete the learning process.
Step 5: After the contact has been learnt, set the control unit to "Walk Test" mode, by holding the contact in the desired
position and press the Test button to check that it is within the wireless range of the control unit.
Step 6: After having checked the correct position of contact, proceed with the installation.
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
Step 1:
Install the contact using one of the methods described below.
Step 2:
Install the magnet on the part with the most movement (such as a door) using the screws supplied (double-
sided tape is provided only if drilling is not possible).
Align the magnet with the indicators of the contact.
If necessary, use the magnet spacer to correctly align it with the indicators.
<
<
N
N
O
O
T
T
E
E
>
>
With the door closed, the magnet must be at a distance of less than 15 mm from the detector.
I
I
n
n
s
s
t
t
a
a
l
l
l
l
a
a
t
t
i
i
o
o
n
n
m
m
e
e
t
t
h
h
o
o
d
d
There are two ways to install the contact: with double-sided adhesive tape or with screws.
Installation with double-sided adhesive tape (exceptional cases only)
I.
Clean the surface using a suitable degreaser.
II.
According to the installation side, remove the protective film from one of the
sides of the double-sided tape and make it adhere firmly to the back of the
device.
III.
Remove the other protective film and make it adhere tightly to the contact in
the desired position.
<
<
N
N
O
O
T
T
E
E
>
>
Do not use the installation method with double-sided adhesive tape on surfaces with
peeling or cracked paint or on uneven surfaces.
Install the contact on the part which does not move (as the frame of a door or a
window) and install the magnet on the moving object (such as the door or the
window). Carefully check that the rubber cap mounted on the tamper switch is still in
place.
Installation with screws
The base is provided with provisions where the plastic is thinner to allow installation.
To fit the contact:
I.
Remove the cover by undoing the retaining screws.
II.
Break the areas provided on the base.
III.
Using a template for the holes, make the holes in the wall.
IV.
Insert the anchor bolts if the device is fixed to plaster or bricks.
V.
Screw the base into the anchor bolts.
VI.
Secure the cover to the base and tighten the cover fixing screws. Carefully check
that the rubber cap mounted on the tamper switch is still in place.
T
T
e
e
c
c
h
h
n
n
i
i
c
c
a
a
l
l
s
s
p
p
e
e
c
c
i
i
f
f
i
i
c
c
a
a
t
t
i
i
o
o
n
n
s
s
Power supply: 1 3V CR2 lithium battery
Battery life: 10 years (typical value, can vary according to use)
Two-way radio frequency 868.6375 MHz
Working temperature range -10°C to +45°C
Dimensions: 85 mm x 25 mm x 20 mm
Weight: 100g
Compliant with EN 50131 Grade 2, Class
Ⅱ
SIMPLIFIED EU DECLARATION OF CONFORMITY
The manufacturer, URMET S.p.A., hereby declares that the wireless device: DC600 10A DC600 MINI MAGNETIC CONTACT
complies with Directive 2014/53/EU. The complete EU Declaration of Conformity can be downloaded from the following Internet
address:
www.elkron.com
Door /
Window
Provisions
Frame
