02-58/2016 Rev.8
RFSA-61M, RFSA-66M
Wireless switch unit
EN
Made in Czech Republic
ANT.
RFSA-61M
Un STATUS
PROG
xxxxxx
RFSA-66M
ANT.
Un
1:011111
2:011112
3:011113
4:011114
5:011115
6:011116
ST
ATUS
PR
OG
Indication, manual control /
LED Un
LED STATUS
antenna connector /
button /
LED Un
antenna connector /
LED STATUS for individual channels /
PROG buttons for individual channels /
• LED Un - green - power supply indication.
• LED STATUS - red - status indication of individual channels.
Indicators of memory function:
On - LED blinks x 3.
Off - The LED lights up once for a long time.
• Manual control is performed by pressing the PROG button for less than 1s.
• Programming is performed by pressing the PROG button for more than 1s.
In the programming and operating mode, the LED on the component lights up at the same time
each time the button is pressed - this indicates the incoming command.
1
2
3
1 x
PROG
>
1s
1 x
PROG
<
1s
1 x
1 x
Functions and programming with RF transmitters /
Function button /
Description of button /
Programming /
Press of programming button
on receiver RFSA-61M (66M)
for 1 second will activate re
-
ceiver RFSA-61M (66M) into
programming mode. LED is
flashing in 1s interval.
Select and press one button
on wireless switch, to this but-
ton will be assigned function
Button.
Press of programming button
on receiver RFSA-61M (66M)
shorter then 1 second will fin-
ish programming mode. The
LED lights up according to the
pre-set memory function.
Compatibility /
The device can be combined with all system components, controls and devices
of iNELS RF Control and iNELS RF Control
2
.
The detector can be assigned an iNELS RF Control
2
(RFIO
2
) communication
protocol.
0524
01234
5
2/7
The output contact will be closed by pressing the button and opened by releasing
the button.
For the correct execution of individual commands (press = closing / releasing the
button = opening), the time delay between these commands must be a min of .
1s (press - delay 1s - release).
U-Energister, d.o.o.| Noveških interniraca 1V | 31000 Užice | Serbia | e-mail: [email protected]
U-Energister, d.o.o. | Norveških interniraca 1V | 31000 Užice | Republika Srbija | e-mail: [email protected]
EN
Support: +381 63 479 880 |
RS
Tehnička podrška +381 63 479 880
www.elkoep.rs
Jednokanalna prekidačka jedinica
RS
Indikacije, ručna kontrola
konektor za antenu
taster PROG
konektor antene
LED STATUS za pojedinačne
kanale
taster PROG za pojedinačne kanaley
• LED Un - zelena - indikacija napona napajanja.
• LED STATUS - crvena - indikacija statusa pojedinih kanala.
Indikacija funkcije memorije:
uključeno - LED trepće 3 puta.
isključeno - LED svetli jednom duže vreme.
• Ručni rad se vrši pritiskom na dugme PROG <1s.
• Programiranje se vrši pritiskom na dugme PROG> 1s.
U režimu programiranja i brisanja, svaki put kada se pritisne taster na kontroleru, LED na ele
-
mentu dugo svetli - to znači da je komanda primljena.
Funkcije i programiranje RF kontrolera
Funkcija taster
Opis funkcije taster
Programiranje
Pritiskom na taster za pro-
gramiranje na RF elementu
RFSA-61M (66M) tokom 1 s
element se prebacuje u re-
žim programiranja. LED lam
-
pica trepće u intervalima od
1 sekunde.
Pritiskom na taster po vašem
izboru na RF kontroleru taste-
ru dodeljuje funkciju.
Pritiskom na taster za pro-
gramiranje na RFSA-61M
(66M) kraćim od 1 sekunde
završava se režim programi
-
ranja. LED svetli u skladu sa
podešenom funkcijom me
-
morije.
Kompatibilnost
Element se može kombinovati sa svim sistemskim elementima, kontroleri
-
ma i elementima sistema iNELS RF Control i iNELS RF Control
2
.
Detektori obeleženi komunikacijskim protokolom
iNELS RF Control
2
(RFIO
2
)
takođe se mogu dodeliti elementu.
Izlazni kontakt zatvara se pritiskom na taster, otvara se otpuštanjem tastera.
Za pravilno izvršavanje pojedinih naredbi (pritisnite = zatvaranje / otpuštanje
tastera = otvaranje) vremensko kašnjenje između ovih naredbi mora biti min.
1s (pritisnite - sačekajte 1s - otpustite).
