2 3
22
W W W. I N E L S . C O M / K I T S
U S E R ´S M A N U A L 2 . 0
ASSIGN OTHER UNITS
Menu (create names)
1.
Press the ADD icon
(Fig. 2) to show a list of sections (Fig. 3)
Temperature regulation Switching Dimming Blinds Shutters Quick control
Choose the section where you want to add new name for your device
and type your own text (max. 20 characters).
Fig. 2
Fig. 2
Fig. 4
Fig. 4
Fig. 1
l
Fig. 1
Fig. 3
Fig. 3
ASSIGN OTHER UNITS
Programming / assign a new device
2.
Click on the Add/Assing new (Fig. 3). A list of units from selected section will be shown (Fig. 4). Click
and select the actuator which you want to assign to Wireless RF Touch. Enter the address of actuator
you want to assign - Fig. 5 (address indicated on the actuator). Confirm with
OK
.
From the menu location, select the name to which the actuator will be assigned (Fig. 6, Fig.7).
Note: Only one name can be assigned to each actuator. When programming, wireless actuator must
be connected with the installation.
COMMMUNICATION TEST
(Fig. 8)
used to detect and display the current status of the RF signal between the
RF Touch and programmed actuator.
Press Start
(Fig. 9) to initiate the test, the current status of the signal is
displayed in percentage. If it is less than 20 %, please relocate the unit or
use Repearer (RFRP-20).
Press Return
to Programming to get back to the main menu of programming.
Note: Communication test can not be performed for battery powered devices.
Fig. 5
Fig. 5
room 1
Fig.
7
Fig.
7
Fig.
5
Fig.
5
Fig.
3
Fig.
3
Fig.
3
Fig.
4
Fig.
4
RFATV-1
Fig.
8
Fig.
8
Fig.
9
Fig.
9
Fig.
6
Fig.
6
Fig.
2
Fig.
2
Heating 1
Heating 2
Heating3
at
ing
ng
g
2
2
t
ing
ng
ng
g
2
2
t
ing
ng
g
2
2
t
ing
ng
g
2
2
at
t
i
in
n
n
n
n
ng
g3
g3
g3
g3
g3
Used to assign the wireless units to menu you created in the previous step (Menu - create names). In
the menu „Settings“ choose Programming (Fig.1). Units are divided into sections for which they are
intended. According to the actuator‘s type, select a required section - see table below.
Menu (create names) used to add, rename, edit or remove the names of Wireless
units.
The name of wireless units corresponds to the name of controlled appliance (the
kitchen light, the living room light, garage, ...). Creating names is important for
successful programming of the wireless RF Touch.
RF CONTROL ACTUATOR SECTIONS
TEMP. REGULATION
SWITCHING
DIMMING
SHUTTERS
DETECTORS
RFSTI-11B/G
RFSA-11B
RFDA-11B
B RFJA-12B/230V
JA-81M / 82M
RFTI-10B INX
RFSA-6X*
RFDA-71B
RFJA-12B/24V DC
JA-80P
RFTI-10B OUTXX
RFDAC-71B
B RFDAC-71B
RFTC-10/G
RFSAI-61B
RFDEL-71B
RFATV-1
RFUS-11
RFDSC-11
RFUS-61
RFDSC-71
RFSC-11
RFSC-61
Fig. 1
Fig. 1