background image

4

PRODUCT SAFETY INFORMATION

• All personnel who may be expected to use this equipment must be thoroughly trained in its safe and 

proper use.

• Before flowing water from this device, check that all personnel (fire service and civilian) are out of the 

stream path.  Also, check to make sure stream direction will not cause avoidable property damage.

• Become thoroughly familiar with the hydraulic characteristics of this equipment, and the pumping 

system used to supply it. To produce effective streams, operating personnel must be properly trained.

• Whenever possible, this equipment should be operated from a remote location. Do not needlessly 

expose personnel to dangerous conditions.

• Open water valves supplying this equipment slowly so that piping fills slowly, thus preventing 

possible water hammer occurrence.

• After each use, and on a scheduled basis, inspect equipment per instructions in the Maintenance 

section.

• Any modifications to the system may destroy the NEMA 4 rating and void warranty coverage.

!

Important: 

Before installing and operating provided equipment, read this manual 

thoroughly. Proper installation is essential to safe operation. 

SYSTEM INFORMATION:

Monitor Serial Number:

Monitor Accessories (Nozzle Gallon Age And Type, Types Of  Transmitters, Water Valve, Etc.):

Summary of Contents for 7100HDX2









































Reviews: